Prescolite ARCHITRAK SYSTEM v.1 - Manual

Instruction
Sheet
www
.prescolite.com
•
Prescolite T
ollFree T
echnical
Support
1.888.PRS.4TEC
• Hours: 8am - 5pm ET
701 Millennium Blvd., • Greenville, SC 29607
With representatives offices in principal cities throughout North America.
Copyright 2008, 09/12 revision, All Rights Reserved - Printed in U.S.A.
Part No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .157820100
Instruction
Sheet
INSTALLATION INSTRUCTIONS
ARCHITRAK ® SYSTEM
INSTALLATION INSTRUCTIONS
FOR PRESCOLITE AKT TRACK FIXTURE ASSEMBLIES
FOR USE WITH PRESCOLITE AKT ONE/TWO CIRCUIT TRACK SYSTEM ONLY
READ INSTALLATION INSTRUCTIONS BEFORE INSTALLING THE TRACK SYSTEM
SAVE INSTRUCTIONS FOR REFERENCE WHEN MAKING ADDITIONS TO OR CHANGES IN THE TRACK SYSTEM
INSTALLATION
TRACK WIRED FOR SINGLE CIRCUIT OPERATION.
1. Refer to PRESCOLITE AKT series track for track installation instructions.
2. Pull plastic cover down on fixture contact head.
3. Insert contact head into PRESCOLITE AKT TRACK RAIL. Twist contact head 1/4 turn (90 degrees) until locking
tab snaps up into place. To remove fixture from track, retract locking tab, turn 1/4 turn, (90 degrees) and remove.
4. If fixture assembly does not light, remove fixture, rotate 180 degrees, reinsert into track and turn 1/4 turn to engage
single circuit.
TRACK WIRED FOR TWO CIRCUIT OPERATION.
1. All fixtures can be placed on circuit one or circuit two. To alternate circuits fixtures are placed on, rotate alternate
fixture 180 degrees.
2. Refer to AKT TRACK RAIL INSTRUCTIONS for circuit identification groove.
NOTE: For lamp type and maximum lamp wattage, refer to relamp label located inside fixture assembly.
CONTACT HEAD
AKT TRACK RAIL
WARNING:
WHEN INSTALLING OR USING THIS TRACK SYSTEM, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS BE FOLLOWED. READ ALL INSTRUCTIONS.
DO NOT INSTALL THIS TRACK IN DAMP OR WET LOCATIONS. DO NOT
INSTALL ANY PART OF TRACK SYSTEM LESS THAN 5 FEET ABOVE FLOOR.
DO NOT INSTALL ANY FIXTURE ASSEMBLY CLOSER THAN 6 INCHES FROM
ANY CURTAIN OR SIMILAR COMBUSTIBLE MATERIAL. DISCONNECT ELEC-
TRICAL POWER BEFORE ADDING TO OR CHANGING THE CONFIGURATION
OF THE TRACK. DO NOT ATTEMPT TO ENERGIZE ANYTHING OTHER THAN
LIGHTING TRACK FIXTURES ON THE TRACK. TO REDUCE THE RISK FIRE
AND ELECTRICAL SHOCK, DO NOT ATTEMPT TO CONNECT POWER TOOLS,
EXTENSION CORDS, APPLIANCES, AND THE LIKE TO THE TRACK.
FIXTURE ASSEMBLY
NOT SHOWN
SAVE THESE INSTRUCTIONS
LOCKING LEVER
FIXTURE ASSEMBLY
PULL LOCKING LEVER
DOWN TO REMOVE
FIXTURE ASSEMBLY
IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information
and instructions concerning Wet or Damp Locations, installation near combustible materials, insulation, building materials,
and proper lamping. Do not install in areas subject to combustible vapors or gases. Before wiring to power supply and
during servicing or relamping, turn off power at fuse or circuit breaker. All servicing or relamping must be performed by
qualified service personnel. Product must be grounded to avoid potential electric shock or other potential hazard.
Product must be mounted in locations and at heights and in a manner consistent with its intended use, and in
compliance with the National Electrical Code and local codes. The use of accessory equipment not recommended by
the manufacturer or installed contrary to instructions may cause an unsafe condition. Do not block light emanating from
product in whole or part, as this may cause an unsafe condition. Do not allow items such as drapes, curtains, screens or
the like to come into contact with the product or to block light from the product, as this may cause an unsafe condition.
WARNING:
2. This Product contains chemicals known to the State of California to cause cancer, birth defects and/or other reproduc-
tive harm. Thoroughly wash hands after installing, handling, cleaning, or otherwise touching this product.