Prescolite CFR8 User Manual
Instruction sheet, Installation instructions cat. no. cfr8, Prs.4tec

Instruction
Sheet
www.prescolite.com
•
Prescolite
TollFree
Technical
Support
1.888.PRS.4TEC
•
Hours:
8am
- 5pm
ET
701 Millennium Blvd.,• Greenville, SC 29607
With representatives offices in principal cities throughout North America.
Copyright 2009, 10/28/09 revision, All Rights Reserved - Printed in U.S.A.
Part No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 05983300
Instruction
Sheet
INSTALLATION INSTRUCTIONS
CAT. NO. CFR8
Reflector
CAUTION: DO NOT ATTEMPT TO MODIFY OR REWIRE FACTORY-INSTALLED WIRING ON THE FIXTURE. SAFETY AND
PROPER OPERATION OF THE FIXTURE DEPEND ON THE INTEGRITY OF THE WIRING.
WARNING- This product contains chemicals known to the State of California to cause cancer, birth defects and/or
other reproductive harm. Thoroughly wash hands after installing, handling, cleaning, or otherwise touching this
product.
1. Bend brackets as shown in Detail “A”.
Install the fixture in the ceiling using
mounting channel or bar (by others)
placed in the adjustable mounting
brackets. Mount the fixture in the ceil-
ing so that the weight of the fixture is
supported by the mounting channel or
bar and/or hanger wires secured to the
building structure.
2. Adjust the fixture so the bottom of the
plaster flange is flush with the finished
ceiling line and in alignment with adja-
cent fixtures. Secure mounting brackets
by tightening wing nuts on either side of
the fixture.
3. Remove J-Box cover plate. Remove
appropriate knockout and assemble
appropriate connector for the supply
wire used. Connect ground wires to
green ground leads. Connect white (com-
mon) to white (leads). Connect power
supply (line) to black lead(s). Reinstall
J-Box cover.
WARNING: DO NOT pinch wires
between J-Box/ballast cover
and J-Box. Consult a Qualified
Electrician for all other options
that require other wiring configu-
rations. Each circuit may be wired
separately for two circuit installations.
4. Connect the Mate-N-Lock
Connectors from the ballast to the
connectors from the fixture. Push
all connectors and splices into the J-Box.
5. Install the ballast assembly by positioning
the tab on the ballast mounting plate in
the slot on the J-Box bottom plate. Secure
ballast assembly by snapping plate
under J-Box Spring and bending spring
down (See Detail “B”). WARNING: Do
Not pinch Wires between Ballast
and J-Box or between J-Box and
covers!
6. After all ceiling installation and finishing
work is complete. Install the reflector.
7. Install the proper lamps (by others).
Wing Nut
Tab
NOTE: Brackets are
supplied flat. To
insure proper align-
ment, bend brackets
in line with marks on
flange as shown in
detail “A”.
Press
Spring
Down on
Both Sides
of the
J-Box
DETAIL B
DETAIL “A”
Ballast
Assembly
Bend Brackets in
Line with Marks on
Flange
Mate-N-Lock
Connectors
J-Box
Adjustable
Mounting
Bracket
Marks on
Flange
IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information and
instructions concerning Wet or Damp Locations, installation near combustible materials, insulation, building materials, and
proper lamping. Do not install in areas subject to combustible vapors or gases. Before wiring to power supply and during
servicing or relamping, turn off power at fuse or circuit breaker. All servicing or relamping must be performed by
qualified service personnel. Product must be grounded to avoid potential electric shock or other poten-
tial hazard. Product must be mounted in locations and at heights and in a manner consistent with its
intended use, and in compliance with the National Electrical Code and local codes. The use of accessory
equipment not recommended by the manufacturer or installed contrary to instructions may cause an unsafe condition. Do
not block light emanating from product in whole or part, as this may cause an unsafe condition. Do not allow items such
as drapes, curtains, screens or the like to come into contact with the product or to block light from the product, as this may
cause an unsafe condition.