Prescolite SDPS6LED User Manual

Ins tru ctio n s he et, For sdpsled for rdpsled, For sdpsled

Ins

tru

ctio

----

-w

olit

e.c

• P

res

lite

llF

ree

nic

al S

1.8

.4T

•

rs:

- 5

Part No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93012106

701 Millennium Boulevard • Greenville, SC 29607

With representatives offices in principal cities throughout North America.

Ins

tru

ctio

INSTALLATION INSTRUCTIONS

SDPS6LED SERIES

MOUNTING
PLATE

BLACK

GREEN

WHITE

J-BOX

1. LOOSEN SCREWS ON J-BOX HALF WAY

(SUPPLIED BY OTHERS).

2. LOCATE THE BLACK (LINE), WHITE (COMMON), &

GREEN (GROUND) WIRES IN THE FIXTURE WIRING

COMPARTMENT AND PASS THESE WIRES THROUGH

CENTER HOLE OF MOUNTING PLATE AS SHOWN IN TOP

FIGURE.

3. (DIMMING ONLY) THERE WILL BE A GRAY AND VIOLET

WIRE (1 EACH). PASS THESE THROUGH HOLE WITH

OTHER WIRES.

4. ALIGN MOUNTING PLATE TO J-BOX, ROTATE PLATE

COUNTERCLOCKWISE, AND TIGHTEN WITH SCREWS.

NOTE: THE FIXTURE SHOULD BE ALLOWED TO HANG

ON ITS CHAIN AT THIS POINT.

5. REMOVE J-BOX COVER PLATE. REMOVE APPROPRIATE

KNOCKOUT AND ASSEMBLE APPROPRIATE CONNEC-

TOR FOR THE SUPPLY WIRE USED. CONNECT GROUND

WIRES TO GREEN GROUND LEADS. CONNECT WHITE

(COMMON) TO WHITE (LEADS). CONNECT POWER SUP-

PLY (LINE) TO BLACK LEAD(S). (DIMMINING ONLY) CON-

NECT GRAY (+) AND VIOLET (-) WIRES TO APPROPRIATE

0-10V DIMMING CONTROL PER NATIONAL ELECTRICAL

CODE AND ALL LOCAL CODES. REINSTALL J-BOX

COVER.

WARNING: DO NOT PINCH WIRES BETWEEN

J-BOX/BALLAST COVER AND J-BOX. CONSULT A

QUALIFIED ELECTRICIAN FOR ALL OTHER OPTIONS

THAT REQUIRE OTHER WIRING CONFIGURATIONS.

6. PUSH THE SPLICES INTO THE J-BOX. HOLD UP THE FIX-

TURE WHILE DOING THIS TO PREVENT STRAIN ON THE

BLACK AND WHITE WIRES.

7. PUSH CHAIN AND GREEN BRACKET GROUND WIRE

INSIDE COVER.

8. ALIGN SIDE HOLES ON CANOPY TO SIDE HOLES ON

MOUNTING BRACKET AND FASTEN WITH FLAT HEAD

SCREWS SUPPLIED (FIG 3.).

CAUTION:

DO NOT ATTEMPT TO MODIFY OR REWIRE

FACTORY-INSTALLED WIRING ON THE FIX-

TURE. SAFETY AND PROPER OPERATION OF

THE FIXTURE DEPEND ON THE INTEGRITY OF

THE WIRING.

KEEP THESE INSTRUCTIONS

IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information

and instructions concerning Wet or Damp Locations, installation near combustible materials, insulation, building materials,

and proper lamping. Do not install in areas subject to combustible vapors or gases. Before wiring to power supply and

during servicing or relamping, turn off power at fuse or circuit breaker. All servicing or relamping must be performed by

qualified service personnel. Product must be grounded to avoid potential electric shock or other potential hazard.

Product must be mounted in locations and at heights and in a manner consistent with its intended use, and in

compliance with the National Electrical Code and local codes. The use of accessory equipment not recommended by

the manufacturer or installed contrary to instructions may cause an unsafe condition. Do not block light emanating from

product in whole or part, as this may cause an unsafe condition. Do not allow items such as drapes, curtains, screens or

the like to come into contact with the product or to block light from the product, as this may cause an unsafe condition.

WARNING - This product contains chemicals known to the State of California to cause cancer, birth defects, and/or other

reproductive harm. Thoroughly wash hands after installing, handling, cleaning, or otherwise touching this product.

DRIVER

GROUND WIRE

WHITE TO WHITE

BLACK TO BLACK

WIRENUT (3)

(NOT SUPPLIED)

CHAIN

DRIVER HEAT SINK

BRACKET GROUND

WIRE

CANOPY

JBOX GREEN

GROUND WIRE

MOUNTING

BRACKET

FOR SDPSLED

FIG 2

DRIVER

GROUND WIRE

WHITE TO WHITE

BLACK TO BLACK

WIRENUT (3)
(NOT SUPPLIED)

CHAIN

DRIVER HEAT SINK
BRACKET GROUND
WIRE

CANOPY

JBOX GREEN
GROUND WIRE

MOUNTING
BRACKET

8-32 FLAT HEAD
SCREWS
(SUPPLIED)

CAPTIVE SCREW

LIGHT ENGINE
WIRE ASSEMBLY

DRIVER
WIRE ASSEMBLY

SAFETY
CABLE

FOR SDPSLED

FOR RDPSLED

CEILING OUTLINE

FIG 2

FIG 3

FIG 4