Ins tru ctio n s he et, For sdpsled for rdpsled, W.p re sc olit e.c om – Prescolite RDPS6LED User Manual

Page 2

olit

e.c

• P

res

lite

llF

ree

nic

al S

1.8

.4T

•

rs:

- 5

Part No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93012107

Ins

tru

ctio

6. CONNECT “S” HOOK IN FREE KEYHOLE OF PLASTER

FLANGE. ALLOW PENDANT TO HANG FREELY ON SAFETY

CABLE. SEE FIG 2C

7. LOCATE THE RED AND BLUE WIRES FROM PENDANT

ASSEMBLY AND PASS WIRES AND PROTECTIVE SLEEVE

THROUGH SLOTTED HOLE IN PENDANT BRACKET.

8. CONNECT WIRES FROM DRIVER HOUSING TO WIRES FROM

PENDANT (RED TO RED, BLUE TO BLUE) SECURING WITH

WIRE NUTS SUPPLIED.

9. PUSH WIRES BACK INTO HOUSING. ALL WIRES MUST BE

RUN THROUGH CENTER OF SLOTTED HOLE OF PENDANT

BRACKET. STRAIN RELIEF ON PROTECTIVE SLEEVE MUST

BE LOCATED ON INSIDE FACE OF PENDANT BRACKET

BEFORE SECURING MOUNTING PLATE IN PLACE.

10. HOLD PENDANT UP TO HOUSING FIXTURE, ALLOWING CEIL-

ING COVER TO REST AT BOTTOM OF STEM DISENGAGE “S"

HOOK AND ALLOW SAFTY CABLE (WITH “S” HOOK) TO HANG

OUT SIDE OF HOUSING FIXTURE.

11. ALIGN HOLES OF PENDANT COVER PLATE TO HEX SCREWS

ON PENDANT BRACKET. TURN COUNTER-CLOCKWISE AND

TIGHTEN HEX SCREWS. SEE FIG 7.

12. PUSH “S” HOOK AND CABLE UP INTO HOUSING FIXTURE.
13. MOUNT CEILING COVER BY INSERTING TORSION SPRINGS

THROUGH SLOTS. SEE FIG 5B.

LED ARRAY REPLACEMENT

1. REMOVE THE TRIM BY LOOSING THE CAPTIVE SCREW.

2. DISCONNECT LIGHT ENGINE WIRE ASSY FROM DRIVER

WIRE ASSY.

3. LOOSEN AND REMOVE SAFETY CABLE FROM BOTTOM OF

REFLECTOR SUB-ASSEMBLY.

4. REMOVE (3) MOUNTING SCREWS FROM REFLECTOR.

REPLACE LIGHT ENGINE AND SECURE WITH (3) MOUNTING

SCREWS.

5. RECONNECT SAFETY CABLE TO LOWER HOLE IN REFLEC-

TOR. CONNECT REPLACEMENT LIGHT. ENGINE WIRE ASSY

TO DRIVER WIRE ASSY.

6. SLIDE REFLECTOR AND LIGHT ENGINE SUB ASSEMBLY IN

PLACE.

7. TIGHTEN CAPTIVE SCREW.

LED DRIVER REPLACEMENT
1. REMOVE PENDANT FROM HOUSING REVERSING INSTRUC-

TIONS IN STEPS 3-13 ABOVE. DISCONNECT ALL WIRING

NECESSARY TO REMOVE DRIVER. REMOVE (2) 8-32

SCREWS SECURING DRIVER. (SUPPLIED). REPLACE OLD

DRIVER WITH NEW ONE BY TIGHTENING THE 2 DRIVER

MOUNTING SCREWS. RECONNECT ALL WIRING REFERENCE

STEPS 2 AND 8 OF INSTALLATION INSTRUCTIONS

TORSION SPRING

PENDANT

BRACKET

SLOT FOR TORSION

SPRING (2X)

CEILING COVER

RETAINER

RING

STEM AND

PENDANT

COVER PLATE

BALL HALF

701 Millennium Boulevard • Greenville, SC 29607

With representatives offices in principal cities throughout North America.

FIG. 4

FIG. 5B

FIG. 5A

FIG. 7

TAMPER PROOF
SCREW

FIG 6

LIGHT ENGINE
WIRE ASSEMBLY

DRIVER WIRE
ASSEMBLY

DRIVER

GROUND WIRE

WHITE TO WHITE

BLACK TO BLACK

WIRENUT (3)
(NOT SUPPLIED)

CHAIN

DRIVER HEAT SINK
BRACKET GROUND
WIRE

CANOPY

JBOX GREEN
GROUND WIRE

MOUNTING
BRACKET

8-32 FLAT HEAD
SCREWS
(SUPPLIED)

TAMPER PROOF SCREW

LIGHT ENGINE
WIRE ASSEMBLY

WIRE ASSEMBLY

SAFETY
CABLE

FOR SDPSLED

FOR RDPSLED

CEILING OUTLINE

FIG 2

FIG 3

FIG 4