Avaya IP Office Phone - Manual (Page 79)

Technical Data Technical Specifications - Page 79
IP Office Installation Manual Technical Data - Page 79
40DHB0002USCL – Issue 9 (28th October 2003) Technical Specifications
Technical Specifications
General
Dimensions
(unboxed) IP401: Width: 255mm (10"). Height: 71mm (2.8") Depth: 235mm (9.3")
IP403/6/12 & Exp. Modules : Width: 445mm (17.5") Height: 71mm (2.8") Depth: 245mm (9.7")
Dimensions
(boxed) IP401: Width: 304mm (13.4") Height: 105mm (4.2") Depth: 305mm (12")
IP403/6/12 & Exp. Modules : Width: 445mm (17.5") Height: 71mm (2.8") Depth: 245mm (9.7")
Environmental 0 to +40 °C. 95% relative humidity, non-condensing.
Weight (unboxed)
Kgs
lbs 401 403 406 412 Analog16 DT/DS16 DT/DS30 WAN3 So8 Phones8 …16 …30
1.2 2.6 3.0 3.0
2.9 3.0 3.50 2.8 2.8 2.8 2.9 3.10
2.6 5.8 6.6 6.7 6.5 6.7 7.8 6.3 6.3 6.3 6.5 6.94
Weight (boxed)
Kgs
lbs 401 403 406 412 Analog16 DT/DS16 DT/DS30 WAN3 So8 Phones8 …16 …30
2.4 3.85 4.3 4.3
4.2 4.3 4.8 4.1 4.1 4.1 4.2 4.4
5.4 8.6 9.6 9.6 9.4 9.6 10.8 9.2 9.2 9.2 9.4 9.7
Power Supply
Consumption
(nominal Watts) 2.5mm DC inlet socket. 24Vdc Power input. Rating 24Vd.c., 2A max.
401 403 406412 Analog16 DT/DS16 DT/DS30 WAN3 So8 Phones8 …16 …30
24 26 16 17.5 5 24 30 12 24 12 16 30
Lump-in-Line PSU Power Requirements: I/P 100-240Vac, 50/60Hz, 81-115VA, Input current 2A max
Standard PSUs: O/P 24Vdc, 1.875A, output power 45W max.
DS30 80W PSU: O/P 16Vdc, 5A, output power 80W max.
Lump-in-line PSUs are CE/UL/Dentori Safety Approved.
Interfaces
Interface Information
DTE 25 way D-Type female connector, V.24/V.28. (9 way D-type on IP412s)
ISDN ROW Interfaces:
BRI :
RJ45 sockets. ETSI S/T Interface to CTR3 for Pan European Connection.
PRI E1: RJ45 socket. ETSI T Interface to CTR4 for Pan European Connection.
PRI E1-R2: RJ45 socket. ETSI T Interface to CTR4 for Pan European Connection.
PRI E1-R2: 75
Ω BNC Coax.. ETSI T Interface.
PRI T1: RJ45 socket: FCC Part 68/JATE connection.
USA Interfaces:
PRI T1 Service:
Ground Start (GS) – Default, E&M, 56k data for 5ESS, 56/64/64 restricted for 4ESS
PRI ISDN Switch support:
4ESS, 5ESS, DMS-100, DMS-250 (includes conformance to ANSI T1.607 & Bellcore
Special Report SR4287, 1992
PRI ISDN Services:
AT&T Megacom 800, AT&T WATS (4ESS), AT&T SDS Accunet 56kB/s & 64kB/s (4ESS),
AT&T Multiquest (4ESS).
Analog ports RJ45 sockets: Loop start/Ground start (region dependant)
Power Fail ports RJ45 sockets: telephone ports act as master sockets
ISDN
Data Rates BRI: B-channel 64kbps or 56kbps, D-channel 16kbps.
PRI: B-channel 64kbps or 56kbps, D-channel 64kbps.
Telephone RJ45 sockets. EU - Telephone ports act as master sockets.
CLI Schemes: DTMFA, DTMFC, DTMFD, FSK and UK20.
REN = 2
Off Hook current = 25mA.
Ring Voltage = 40V (nominal) RMS.
External Bell (via analog port); REN = 1
LAN RJ45 sockets. Auto-negotiating 10/100BaseT Ethernet (10Mbps).
Port 8 is MDI/MDIX switchable via the adjacent Cascade pushbutton switch.
Refer to pages 11, 15 and 19.
WAN 37 way D-Type female sockets. X.21 interface to 2048k bps, V.35 interface to 2048k bps and
V.24 Interface to 19k2 bps.
Audio 3.5mm Stereo Jack socket. Input impedance - 10k /channel.
Maximum a.c. signal – 200mV rms.
External
Control 3.5mm Stereo Jack socket. Switching Capacity - 0.7A.
Maximum Voltage - 55V d.c. On state resistance - 0.7
Ω.
Short circuit current - 1A. Reverse circuit current capacity - 1.4A.