Allied Telesis x510 Series - Manual (Page 7)

7
Figure 1: Front Panels of the AT-x510-28GTX and AT-x510-28GPX Switches ...................................................................19
Figure 2: Front Panels of the AT-x510-28GSX, AT-x510-52GTX, and AT-x510-52GPX Switches......................................20
Figure 3: Back Panel of the AT-x510-28GTX, AT-x510-52GTX, and AT-x510-28GSX Switches ........................................21
Figure 4: Back Panel of the AT-x510-28GPX and AT-x510-52GPX Switches .....................................................................21
Figure 5: x510 Series Management Panel ...........................................................................................................................22
Figure 6: LEDs for the 10/100/1000Base-T Ports on the AT-x510-28GTX and AT-x510-52GTX Switches.........................33
Figure 7: LEDs for the 10/100/1000Base-T Ports on the AT-x510-28GPX and AT-x510-52GPX Switches ........................35
Figure 8: SFP Slot LEDs on the AT-x510-28GSX Switch.....................................................................................................36
Figure 9: SFP+ Slot LEDs ....................................................................................................................................................37
Figure 10: Switch ID LED .....................................................................................................................................................39
Figure 11: Switch ID LED .....................................................................................................................................................39
Figure 12: Switch ID LEDs in the Low Power Mode .............................................................................................................40
Figure 13: Stacking Transceivers .........................................................................................................................................48
Figure 14: Stack of Two Switches in the Linear Topology....................................................................................................50
Figure 15: Stack of Four Switches in the Linear Topology ...................................................................................................51
Figure 16: Stack of Two Switches in the Ring Topology ......................................................................................................52
Figure 17: Stack of Four Switches in the Ring Topology......................................................................................................53
Figure 18: PORT Parameter in the Command Line Interface...............................................................................................56
Figure 19: Components of the x510 Series Switches...........................................................................................................65
Figure 20: Turning the Switch Upside Down ........................................................................................................................69
Figure 21: Removing the Rubber Feet .................................................................................................................................69
Figure 22: Attaching the Equipment Rack Brackets .............................................................................................................70
Figure 23: Attaching the Equipment Rack Brackets (Continued) .........................................................................................71
Figure 24: Mounting the Switch in an Equipment Rack ........................................................................................................71
Figure 25: Connecting the Management Cable to the Console Port ....................................................................................75
Figure 26: User Exec Mode Prompt .....................................................................................................................................76
Figure 27: Moving to the Privileged Exec Mode with the ENABLE Command .....................................................................76
Figure 28: Moving to the Global Configuration Mode with the CONFIGURE TERMINAL Command ..................................76
Figure 29: Activating VCStack with the STACK ENABLE Command...................................................................................77
Figure 30: Returning to the Privileged Exec Mode with the EXIT Command .......................................................................77
Figure 31: Saving the Change with the WRITE Command ..................................................................................................77
Figure 32: Rebooting the Switch with the REBOOT Command ...........................................................................................77
Figure 33: Removing the Dust Plug from the S1 Slot ...........................................................................................................80
Figure 34: Removing the Dust Cover from the AT-StackXS/1.0 Transceiver.......................................................................81
Figure 35: Installing the AT-StackXS/1.0 Transceiver in Slot S1..........................................................................................82
Figure 36: Removing the Dust Plug from the S2 Slot ...........................................................................................................83
Figure 37: Installing the AT-StackXS/1.0 Transceiver in Slot S2..........................................................................................84
Figure 38: Handle on the AT-StackOP/0.3 and AT-StackOP/9.0 Transceivers....................................................................85
Figure 39: Installing the AT-StackOP/0.3 or AT-StackOP/9.0 Transceiver ..........................................................................86
Figure 40: Removing the Dust Cover from a Stacking Transceiver......................................................................................87
Figure 41: Positioning the Handle in the Upright Position ....................................................................................................87
Figure 42: Connecting the Fiber Optic Cable to the Stacking Transceiver...........................................................................88
Figure 43: Plugging in the AC Power Cords .........................................................................................................................91
Figure 44: SHOW STACK Command...................................................................................................................................95
Figure 45: Moving to the Global Configuration Mode with the CONFIGURE TERMINAL Command ..................................96
Figure 46: Returning to the Privileged Exec Mode ...............................................................................................................97
Figure 47: Saving the Priority Values with the WRITE Command........................................................................................97
Figure 48: Switch Initialization Messages.............................................................................................................................98
Figure 49: Switch Initialization Messages (Continued) .........................................................................................................99
Figures