beautypg.com

1 waypoints - alter, delete or insert, 2 display of actual coordinate, Operating manual flytec 6020 – Flytec 6020 * User Manual

Page 21: Ins del wp wp, Fiesch

background image

Operating Manual Flytec 6020

2.6.4.1 Waypoints - alter, delete or insert

Waypoints

--------------

Flytec

Fiesch

In this position of Setup-Menu the waypoints may be managed. Waypoints may also be set
comfortably on the PC by use of the „Flychart 4.52“ PC-Software and be transferred
via the PC-interface to the instrument.
Using Menu

Waypoints prompts a list with the waypoints

stored in memory. If this list contains more than the visible 6
waypoints, a down arrow

Ð at the right lower edge of the list

warns that more pages are to follow. To scroll down page by
page, press the

► key, now WP 7 … 12 are displayed etc.


Using the keys

▲ and ▼ it is possible to select an

individual WP for editing after pressing the

OK

key.

Flims, Station

Cassons Grat

---------------⇓

Waypoint 2

Fiesch

Alti 1048 m

N 46’ 24.446

The 1st letter of the WP name will blink. Again
with the

▲ and ▼ keys the required letter is selected; there are

numbers, letters, as well as a set of special characters to
choose from. By pressing the

► key one moves forward to the

E 008’ 08.264

----------------

Ins

Del

WP

WP

next letter etc. With the

F1

key one can shift between capitals

and minuscule. With the

F2

key one single character is deleted

(Rub out). You can enter a maximum of 16 numeric.
Once the name has been entered completely, confirm by pressing

OK

. Now the waypoint

altitude will blink, requiring any alterations. With the

▲▼ keys the altitude value is entered

and confirmed by pressing

OK

. Now the position of WP is next. At first the latitude is entered

in degrees and confirmed with

OK

, after that the minutes, confirmed by

OK

and then the

decimals of the minutes. The same procedure is applied for the longitude. Holding the key
down for a longer moment, changes the values to be set faster.

Delete Waypoints:
The selection of WP’s to be deleted is effected with the

▲ and ▼ keys.

Pressing the

F2

key (Del WP) enables the deleting function, for data safety the 6020-GPS

is asking again: “Delete Waypoint?”. The reply “Yes” or “No” is at choice, but it is also
possible to discontinue the deleting procedure by use of the

Page/ESC

On/Off

key and return to one level

before.

Insert Waypoints:
Pressing the

F1

key (Ins WP) enables this function. Entering waypoint names, altitude and

position is operated by following the same scheme as described above. After confirming all
entries with the

OK

key, the new WP is inserted in alphabetical order to the list. In total up to

200 WP can be saved in the 6020-GPS instrument.

Caution: after inserting the new waypoints, (for ex. entry of a new Route) these can be used
only, if in between one has switched back to the normal flight mode by pressing Esc.
Furthermore, the Route into which the new waypoint should be inserted must not be active.
Therefore, first change into route selection by prolonged pressing of the

key and

deactivate the Route with the help of the

F2

key (Cancel Route).


The more waypoints there are in memory, the more slowly becomes the navigation in the
Main Setup Menu, because the list is always tabulated again in the background.


2.6.4.2 Display of actual Coordinate

If the 6020-GPS receives satellites by GPS-Receiver, the actual position is displayed
by short pressing of the

i

key in the instrument’s information field. After 20 sec. the

previous display screen will automatically reappear. This function is useful in relaying

- 21 -