Horner APG XL6 OCS HEXT351C112 User Manual
Page 5
MAN0885-04-EN
Specifications / Installation
__________________________________________________________________________________________________________________________________________________________________
3/2/2010
Page 5 of 6 #1037
4.5
Power Port and Wiring
5
Wiring and Jumpers
Wire according to the type of inputs / outputs used, and select the
appropriate jumper option.
5.1
I/O Jumpers Settings (JP1 - JP2)
5.2
Wiring Examples
J1 Orange
Terminal
Connector
Name
I1
IN1
I2
IN2
I3
IN3
I4
IN4
I5
IN5
I6
IN6
I7
IN7
I8
IN8
H1
HSC1 /IN9
0V
Ground
A1
Analog IN1
A2
Analog IN2
A3
Analog IN3
A4
Analog IN4
0V
Ground
J2 Black
Terminal
Connector
Name
C6
Relay 6 COM
R6
Relay 6 NO
C5
Relay 5 COM
R5
Relay 5 NO
C4
Relay 4 COM
R4
Relay 4 NO
C3
Relay 3 COM
R3
Relay 3 NO
C2
Relay 2 COM
R2
Relay 2 NO
C1
Relay 1 COM
R1
Relay 1 NO
H4
HSC4 / IN12
H3
HSC3 / IN11
H2
HSC2 / IN10
6
Filter
Filter Constant sets the level of digital filtering according to the following chart.
Digital Filtering. The illustration above demonstrates the effect of digital filtering (set with Filter Constant)
on module response to a temperature change.
Primary Power Port Pins
Pin
Signal
Description
1
Ground
Frame Ground
2
V-
Input Power Supply Ground
3
V+
Input Power Supply Voltage
I1
0V
001XLE036
12-24VDC
I1
0V
Positive Logic In Negative Logic In
Positive Logic vs. Negative Logic Wiring
The XL6 HEXL102
can be wired for Positive Logic
inputs or Negative Logic inputs.
001XLE015
0V ON J1
12-24VDC
R2
C2
R3
C3
R6
C6
R4
C4
R5
C5
R1
C1
H4
H2
H3
LOAD
230VAC
OR
25VDC
N
L
LOAD
230VAC
OR
25VDC
N
L
LOAD
230VAC
OR
25VDC
N
L
LOAD
230VAC
OR
25VDC
N
L
LOAD
230VAC
OR
25VDC
N
L
LOAD
230VAC
OR
25VDC
N
L
J2 Black
Positive Logic
Digital In / Relay Out
Wiring Specifications
For I/O wiring (discrete), use the following wire type or
equivalent: Belden 9918, 18 AWG (0.8 mm
2
) or larger.
For shielded Analog I/O wiring, use the following wire type or
equivalent: Belden 8441, 18 AWG (0.8 mm
2
) or larger.
For CAN wiring, use the following wire type or equivalent:
Belden 3084, 24 AWG (0.2 mm
2
) or larger.
Use copper conductors in field wiring only, 60/75° C
J1 Orange
Positive Logic In
Digital In /
Analog In
I1
I2
I3
I4
0V
A1
A2
0V
I5
I6
I7
I8
A3
A4
H1
001XLE017
12-24VDC
LOOP PWR
20mA
0-10VDC
Note:
Loop Power requirements are determined
by the transmitter specification.
J1
JP2
JP1
J2
001XLE025
60
20
100
40
80
20
0
10
100
90
80
70
60
50
40
30
Scans
0
1
2
3
4
5
6
0
7
%
C
o
m
p
le
te
[
]
Filter
Constant
Location of I/O jumpers (JP2 and JP1) and wiring
connectors
(J1 and J2).
Note:
When using JP2 (A1-A4), e
ach channel can be independently
configured.
Note:
The Cscape Module Setup configuration must match the selected
I/O (JP) jumper settings.
JP1 Digital DC In / HSC
Positive Negative
Logic Logic
Default
A1
A2
A3
A4
JP2 Analog In (A1 – A4)
Current Voltage
(20 mA) (10 V)
Default
Power Connector
Power Up:
Connect to Earth Ground.
Apply 10 - 30 VDC.
Screen lights up.
Torque rating 4.5 – 7 Lb-In
(0.50 – 0.78 N-m)