Horner APG XL10e OCS Built-in I/O Model 2 I/O - Manual

MAN0946-01-EN Specifications / Installation
1/6/2011
Page 1 of 3
1 Specifications
Specifications
Digital DC Inputs Digital Relay Outputs
Inputs per Module
12 including 4 configurable
HSC inputs
Outputs per Module 6 relay
Commons per Module 1 Commons per Module 6
Input Voltage Range 12 VDC / 24 VDC Max. Output Current per Relay 3 A at 250 VAC, resistive
Absolute Max. Voltage 35 VDC Max. Max. Total Output Current 5 A continuous
Input Impedance 10 kΩ Max. Output Voltage 275 VAC , 30 VDC
Input Current Positive Logic Negative Logic Max. Switched Power 1250 VA, 150 W
Upper Threshold 0.8 mA -1.6mA Contact Isolation to XLe ground 1000 VAC
Lower Threshold 0.3 mA -2.1mA
Max. Voltage Drop at Rated
Current
0.5 V
Max Upper Threshold 8 VDC
Expected Life
(See Derating section for chart.)
No load: 5,000,000
Rated load: 100,000
Min Lower Threshold 3 VDC Max. Switching Rate
300 CPM at no load
20 CPM at rated load
OFF to ON Response 1 ms Type Mechanical Contact
ON to OFF Response 1 ms Response Time
One update per ladder scan
plus 10 ms
HSC Max. Switching Rate
10 kHz Totalizer/Pulse, Edges
5 kHz Frequency/Pulse, Width
2.5 kHz Quadrature
Analog Inputs, Medium Resolution
Number of Channels 4
Input Ranges
0 - 10 VDC
0 – 20 mA
4 – 20 mA
Safe input voltage range -0.5 V to +12V
Input Impedance
(Clamped @ -0.5 VDC to 12
VDC)
Current Mode:
100 Ω
Voltage
Mode:
500 k Ω
Nominal Resolution 10 Bits
%AI full scale 32,000 counts
Max. Over-Current 35 mA
Conversion Speed All channels converted once per
ladder scan
Max. Error at 25°C
(excluding zero)
*can be made tighter
(~0.25%) by adjusting the
digital filter setting to 3.
4-20 mA 1.00%
0-20 mA 1.00%
0-10 VDC 1.50%*
Additional error for
temperatures other than 25°C
TBD
Filtering 160 Hz hash (noise) filter
1-128 scan digital running
average filter
2 Wiring and Jumpers
XL Series Built-in I/O – Model 2 I/O
12 DC Inputs, 6 Relay Outputs, 4 Analog Inputs
for XLe, XLt, XL6 (all models) and XL10e
Wiring Specifications
 For I/O wiring (discrete), use the
following wire type or equivalent: Belden
9918, 18 AWG (0.8 mm 2 ) or larger.
 For shielded Analog I/O wiring, use the
following wire type or equivalent: Belden
8441, 18 AWG (0.8 mm 2 ) or larger.
 For CAN wiring, use the following wire
type or equivalent: Belden 3084, 24
AWG (0.2 mm 2 ) or larger.
Use copper conductors in field wiring
only, 60/75° C
Location of I/O jumpers
(JP1 & JP2) and
wiring connectors
(J1 and J2) with back cover
removed.
Note: The Cscape Module Setup configuration must match the
selected I/O (JP) jumper settings.
001XLE026
JP1 Digital DC In / HSC
Positive Negative
Logic Logic
Default 001XLE027
A1
A2
A3
A4
JP2 Analog In (A1 – A4)
Current Voltage
(20 mA) (10 V)
Default
Note: When using JP2 (A1-A4), each channel can be
independently configured.
Jumper Setting Details