Red Lion PAXLCR - Manual (Page 4)

4
3.3 USER INPUT WIRING
CAUTION: DC common (Terminal 4) is NOT isolated from Input common (Terminal 7) or User common (Terminal 9). In order
to preserve the safety of the meter application, DC common must be suitably isolated from hazardous live earth referenced
voltage; or Input common and User common must be at protective earth ground potential. If not, hazardous voltage may be
present at the Signal or User Inputs, and Input or User common terminals. Appropriate considerations must then be given
to the potential of the Input or User common with respect to earth ground.
Terminal 8: User Input
Terminal 9: User Common
3.4 SETPOINT (OUTPUT) WIRING
Terminal 10: NC 1
Terminal 11: NO 1
Terminal 12: Relay 1 Common
Terminal 13: NC 2
Terminal 14: NO 2
Terminal 15: Relay 2 Common
USER INPUT 8
USER COMMON 9
USER INPUT
USER COMMMON 9
8 +
-
10 N.C. 1
COMM 1 12
11 N.O. 1
13
14
15
N.C. 2
N.O. 2
COMM 2
Current Sinking (Active Low Logic)
Current Sourcing (Active High Logic)
3.2 INPUT SIGNAL WIRING
3.1 POWER WIRING
COMMON
+ 24V EXC
4
3
DC Out Power
Terminal 3: + 24 VDC OUT
Terminal 4: Common
Power
Terminal 1: VAC/DC +
Terminal 2: VAC/DC -
1
2
AC/DC
AC/DC
+
-
~
~
2 1
ON
3 4
*
MAGNETIC PICKUP INPUT B
COMMON
INPUT A
COMMON
4
5
6
7
*
5
+24V EXC. 3
t 2 5 A MAX
Resistor to Limit Current
ON
1 2 3
*
4
*
AC
*
5
INPUT A
INPUT B
COMMON 7
6
5
+24V EXC.
COMMON
3
4 1 2
ON
3 4
* *
2.2 kΩ
*
5
INPUT A
INPUT B
COMMON 7
6
5
+24V EXC.
COMMON
3
4
2 1
ON
3 4
* *
O.C.
NPN
*
5
INPUT A
INPUT B
COMMON 7
6
5
+24V EXC.
COMMON
3
4 1 2 3
ON
*
4
*
O.C.
PNP
*
5
INPUT A
INPUT B
COMMON 7
6
5
+24V EXC.
COMMON
3
4 1 2 3 4
ON
*
COMMON
+5 V
*
5
INPUT A
INPUT B
COMMON 7
6
5
+24V EXC.
COMMON
3
4
2 1
ON
* *
3 4
*
5
INPUT A
INPUT B
COMMON 7
6
5
+24V EXC.
COMMON
3
4
*
1 2 3
ON
*
4
*
5
INPUT A
INPUT B
COMMON 7
6
5
+24V EXC.
COMMON
3
4
AC Inputs From Tach Generators, Etc.
Input A
Two Wire Proximity, Current Source
Input A
Magnetic Pickup
Input A
Current Sourcing Output
Input A
Interfacing With TTL
Input A
Current Sinking Output
Input A
Switch or Isolated Transistor; Current Sink
Input A
1 2 3 4
ON
5
INPUT A
INPUT B
COMMON 7
6
5
+24V EXC.
COMMON
3
4
Switch or Isolated Transistor; Current Source
Input A
* Switch position is application dependent.
Current Sink Output; Quad/Direction
Shaded areas not recommended for counting applications.
The meter provides a choice of eight different count modes using two signal inputs,
A and B. The Count Mode selected determines the action of Inputs A and B. Section
5.1, Input Setup Parameters, provides details on count mode selection and input action.