KEPCO EL Series Electronic Load Operator Manual P/N 243-1295 Firmware Version 3.87 to 3.xx - Manual (Page 71)

SERIES EL 022013
B-9
B.38 [SOURce:]CURRent:TRANsient COMMAND
CURR:TRAN
Syntax: Short Form: [SOUR:]CURR:TRAN ,,,
Long Form: [SOURce:]CURRent:TRANsient ,,,
Where:
= = the maximum current value of the transient (Amperes)
= = time (Seconds) from start to end of transient (0.0005 Second minimum)
= = number of times transient is to be repeated (default = 1, maximum = 65,000)
(optional) = = total time (Seconds) of repeating pulse train (must be at least 0.0005
greater than transient )
Description: Configures a transient current pulse that is initiated by SYST:MODE:TRAN (see PAR. B.100).
See PAR. B.106 for details on using both Transient and Ramp commands at the same time. Figure B-
3 on page B-20 shows transient and ramp timing.
B.39 [SOURce:]CURRent:TRANsient? QUERY
CURR:TRAN?
Syntax: Short Form: [SOUR:]CURR:TRAN?
Long Form: [SOURce:]CURRent:TRANsient?
Returns: ,,, (See PAR. B.38 for definitions.)
Description: Returns the transient current pulse parameters established by CURR:TRAN (see PAR. B.38).
B.40 [SOURce:]MODE COMMAND
MODE
Syntax: Short Form: [SOUR:]MODE Long Form: [SOURce:]MODE
where: = CURRent, POWer, VOLTage, RESistance, CONDuctance, SHORT or OFF.
Description: Sets operating mode: When the operating mode is changed, the input is set to off. Send INPut ON to
apply the new mode setting to the load.
B.41 [SOURce:]MODE? QUERY
MODE?
Syntax: Short Form: [SOUR:]MODE? Long Form: [SOURce:]MODE?
Returns: = CURR, POW, VOLT, RES, COND, SHORT or OFF.
Description: Indicates operating mode.
B.42 [SOURce:]POWer[:LEVel][:IMMediate][:AMPlitude] COMMAND
POW
Syntax: Short Form: [SOUR:]POW[:LEV][:IMM][:AMP]
Long Form: [SOURce:]POWer[:LEVel][:IMMediate][:AMPlitude]
Where = power setpoint
Description: Establishes power setpoint. The power setpoint only affects the load when the load is in Power
mode of operation.
B.43 [SOURce:]POWer[:LEVel][:IMMediate][:AMPlitude]? QUERY
POW?
Syntax: Short Form: [SOUR:]POW[:LEV][:IMM][:AMP]?
Long Form: [SOURce:]POWer[:LEVel][:IMMediate][:AMPlitude]?
Returns = power setpoint
Description: Indicates power setpoint.
B.44 [SOURce:]POWer:PROTection COMMAND
POW:PROT
Syntax: Short Form: [SOUR:]POW:PROT Long Form: [SOURce:]POWer:PROTection
where = power protection setpoint
Description: Selects power protection setpoint. This is a user-defined value which, if exceeded during operation,
causes a FAULT condition, forcing the load to disengage.
B.45 [SOURce:]POWer:PROTection? QUERY
POW:PROT?
Syntax: Short Form: [SOUR:]POW:PROT? Long Form: [SOURce:]POWer:PROTection?
Returns = power protection setpoint
Description: Indicates power protection setpoint.