KEPCO EL Series Electronic Load Operator Manual P/N 243-1295 Firmware Version 3.87 to 3.xx - Manual (Page 68)

B-6
SERIES EL 022013
B.16 INPut:RAMP? QUERY
INP:RAMP?
Syntax: Short Form: INP:RAMP? Long Form: INPut:RAMP?
Returns = time (0 to 10,000 msec)
Description: Returns the ramp time established by INP:RAMP. This is the time needed to reach setpoint value
after the load is engaged.
B.17 [SOURce:]INPut:PROTection:CLEar COMMAND
INP:PROT:CLE
Syntax: Short Form: [SOUR:]INP:PROT:CLE Long Form: [SOURce:]INPut:PROTection:CLEar
Description: Resets protection from overcurrent, overpower, etc.
B.18 [SOURce:]INPut:PROTection:SHORt[:STATe] COMMAND
INP:PROT:SHOR
Syntax: Short Form: [SOUR:]INP:PROT:SHOR[:STAT]
Long Form: [SOURce:]INPut:PROTection:SHORt[:STATe]
Description: Applies maximum drive to FETs, effectively shorting the input.
B.19 [SOURce:]OUTPut[:STATe] COMMAND
OUTP
Syntax: Short Form: [SOUR:]OUTP[:STAT] Long Form: [SOURce:]OUTPut[:STATe]
where = 0 or OFF (load disengaged) or 1 or ON (load engaged)
Description: Used to engage or disengage the load from the UUT. When set to 1 the load engages, when set to
0 the load disengages.
B.20 [SOURce:]OUTPut[:STATe]? QUERY
OUTP?
Syntax: Short Form: [SOUR:]OUTP[:STAT]? Long Form: [SOURce:]OUTPut[:STATe]?
Returns = 0 or OFF (load disengaged) or 1 or ON (load engaged)
Description: Indicates whether load is engaged or disengaged from the UUT. When set to 1 the load is
engaged, when set to 0 the load is disengaged.
B.21 [SOURce:]OUTPut:PROTection:CLEar COMMAND
OUTP:PROT:CLE
Syntax: Short Form: [SOUR:]OUTP:PROT:CLE Long Form: [SOURce:]OUTPut:PROTection:CLEar
Description: Resets protection from overcurrent, overpower, etc.
B.22 [SOURce:]OUTPut:PROTection:SHORt[:STATe] COMMAND
OUTP:PROT:SHOR
Syntax: Short Form: [SOUR:]INP:PROT:SHOR[:STAT]
Long Form: [SOURce:]INPut:PROTection:SHORt[:STATe]
Description: Applies maximum drive to FETs, effectively shorting the output.
B.23 [SOURce:]MEASure:ALL? QUERY
MEAS:ALL?
Syntax: Short Form: [SOUR:]MEAS:ALL? Long Form: [SOURce:]MEASure:ALL?
Returns: Measured values in the form 0.000 KW, 0.000 Amps, 0.000 Volts.
Description: Measures output power (Kilowatts), current (Amps), and voltage (Volts). Unit of measurement
included in the reply.
B.24 [SOURce:]MEASure:ALL2? QUERY
MEAS:ALL2?
Syntax: Short Form: [SOUR:]MEAS:ALL2? Long Form: [SOURce:]MEASure:ALL2?
Returns: Measured values in the form 0.000 0.000 0.000 (Kilowatts Amps Volts).
Description: Measures output power (Kilowatts), current (Amps), and voltage (Volts). Unit of measurement is omit-
ted from the reply.