KEPCO BOP 1KW-MG Operator Manual, Firmware Ver.3.05 to 4.07 - Manual (Page 186)

B-32
BOP-1K 031912
B.122 SYSTem:COMMunication:GPIB:ADDRess COMMAND
SYST:COMM:GPIB:ADDR
Syntax: Short Form: SYST:COMM:GPIB:ADDR 0 to 30
Long Form: SYSTem:COMMunication:GPIB:ADDRess 0 to 30
Description:Sets selected power supply GPIB address. NOTE: After executing this command, subse-
quent commands must be directed to the new GPIB address. Requires MEM:UPD (PAR. B.12) to save for
power up. See PAR. 3.5.2.2 and Figure 3-16 for special programming considerations.
B.123 SYSTem:COMMunication:GPIB:ADDRess? QUERY
SYST:COMM:GPIB:ADDR?
Syntax: Short Form: SYST:COMM:GPIB:ADDR?
Long Form: SYSTem:COMMunication:GPIB:ADDRess?
Return Value: 0 to 30
Description: Identifies selected power supply GPIB address.
B.124 SYSTem:COMMunication:SERial:BAUD COMMAND
SYST:COMM:SER:BAUD
Syntax: Short Form: SYST:COMM:SER:BAUD {19200 | 9600 | 4800 | 2400}
Long Form: SYSTem:COMMunication:SERial:BAUD {19200 | 9600 | 4800 | 2400}
Description: Sets the unit to operate at the specified baud rate. See PAR. 3.5.2.2 and Figure 3-16 for special
programming considerations.
B.125 SYSTem:COMMunication:SERial:BAUD? QUERY
SYST:COMM:SER:BAUD?
Syntax: Short Form: SYST:COMM:SER:BAUD?
Long Form: SYSTem:COMMunication:SERial:BAUD?
Return Value: {19200 | 9600 | 4800 | 2400}
Description: Returns operating baud rate.
B.126 SYSTem:COMMunication:SERial:ECHO COMMAND
SYST:COMM:SER:ECHO
Syntax: Short Form: SYST:COMM:SER:ECHO {ON | OFF} or {01 | 00}
Long Form: SYSTem:COMMunication:SERial:ECHO {ON | OFF} or {01 | 00}
Description: Enables (ON) or disables (OFF) echo mode (see PAR. 3.5.6.2.2). Sending ON or 01 causes all sub-
sequent characters to be echoed back. Sending OFF or 00 turns off the character echo after the next
line terminator character. The *RST command has no effect on echo status. See PAR. 3.5.2.2 and Fig-
ure 3-16 for special programming considerations.
B.127 SYSTem:COMMunication:SERial:ECHO? QUERY
SYST:COMM:SER:ECHO?
Syntax: Short Form: SYST:COMM:SER:ECHO?
Long Form: SYSTem:COMMunication:SERial:ECHO?
Return Value: {01 | 00}
Description: Returns 01 when echo mode is active (ON) or 00 when disabled (OFF) (see PAR. 3.5.6.2.2).
B.128 SYSTem:COMMunication:SERial:PACE COMMAND
SYST:COMM:SER:PACE
Syntax: Short Form: SYST:COMM:SER:PACE {NONE | XON}
Long Form: SYSTem:COMMunication:SERial:PACE {NONE | XON}
Description: Enables (XON) or disables (NONE) data flow control via the serial interface (see PAR. 3.5.6.2.1).
See PAR. 3.5.2.2 and Figure 3-16 for special programming considerations.
B.129 SYSTem:COMMunication:SERial:PACE? QUERY
SYST:COMM:SER:PACE?
Syntax: Short Form: SYST:COMM:SER:PACE?
Long Form: SYSTem:COMMunication:SERial:PACE?
Return Value: {01 | 00}
Description: Returns 01 when data flow control via the serial interface is enabled (XON) or 00 when disabled
(NONE) (see PAR. 3.5.6.2.1).