KEPCO BOP 1KW-MG Operator Manual, Firmware Ver.3.05 to 4.07 - Manual (Page 11)

BOP-1K 031912
i
TABLE OF CONTENTS
SECTION PAGE
SECTION 1 - INTRODUCTION
1.1 Scope of Manual ..................................................................................................................................... 1-1
1.2 General Description................................................................................................................................. 1-1
1.3 Specifications .......................................................................................................................................... 1-1
1.4 Local Control ........................................................................................................................................... 1-14
1.5 Remote Control ....................................................................................................................................... 1-14
1.6 Features .................................................................................................................................................. 1-14
1.6.1 Digital Calibration............................................................................................................................... 1-14
1.6.2 voltage/current Protection.................................................................................................................. 1-14
1.6.3 Waveforms......................................................................................................................................... 1-14
1.6.4 Saving and Recalling Settings ........................................................................................................... 1-15
1.6.5 External Reference (Analog Control)................................................................................................. 1-15
1.6.6 External Limits ................................................................................................................................... 1-15
1.6.7 User-defined Voltage/Current Maximum Values (Software Limits) ................................................... 1-15
1.6.8 Parallel and Series Configurations .................................................................................................... 1-15
1.6.9 Energy Recuperation......................................................................................................................... 1-16
1.7 Equipment Supplied ................................................................................................................................ 1-16
1.8 Accessories ............................................................................................................................................. 1-16
1.9 Safety ...................................................................................................................................................... 1-16
SECTION 2 - INSTALLATION
2.1 Unpacking and Inspection ....................................................................................................................... 2-1
2.2 Terminations and Controls ...................................................................................................................... 2-1
2.3 Preliminary Operational Check................................................................................................................ 2-6
2.4 Installation ............................................................................................................................................... 2-8
2.4.1 Rack Mounting................................................................................................................................... 2-8
2.4.2 Slide Installation................................................................................................................................. 2-8
2.5 Wiring Instructions................................................................................................................................... 2-8
2.5.1 Safety Grounding............................................................................................................................... 2-8
2.5.2 Source Power Connections ............................................................................................................... 2-8
2.5.3 D-C Output Grounding....................................................................................................................... 2-8
2.5.3.1 Grounding Network Configuration................................................................................................ 2-9
2.5.4 Power Supply/Load Interface............................................................................................................. 2-9
2.5.5 Load Connection - General................................................................................................................ 2-10
2.5.6 Load Connection Using Local Sensing.............................................................................................. 2-11
2.5.7 Load Connection Using Remote Sensing.......................................................................................... 2-11
2.6 Cooling .................................................................................................................................................... 2-11
2.7 Setting up the unit ................................................................................................................................... 2-11
2.7.1 Consider the Load Type .................................................................................................................... 2-11
2.7.2 Setup for Local Operation.................................................................................................................. 2-11
2.7.3 Setup for Remote Operation via GPIB............................................................................................... 2-13
2.7.4 Setup for Remote Operation via RS 232C......................................................................................... 2-13
2.8 Multiple Unit Configurations .................................................................................................................... 2-13
2.8.1 Multiple Unit Source Power ............................................................................................................... 2-14
2.8.2 Multiple Unit Protection...................................................................................................................... 2-14
2.8.3 Configuring Parallel, Series, 2 X 2 or 3 X 2 combinations ................................................................. 2-19
2.8.4 Operating Instructions for Multiple Unit Combinations....................................................................... 2-23
2.8.5 Restoring a Unit to Standalone Operation......................................................................................... 2-24
2.8.6 Changing Multiple Unit configurations ............................................................................................... 2-24
SECTION 3 - OPERATION
3.1 General.................................................................................................................................................... 3-1
3.2 Power Supply Basics............................................................................................................................... 3-1
3.2.1 Keypad Description............................................................................................................................ 3-1
3.2.2 LCD and Power-up Screen Description............................................................................................. 3-3
3.2.3 Turning the Power Supply On............................................................................................................ 3-5