Climax FF6200 FLANGE FACER - Manual (Page 2)

US Metric
Climax Portable Machining & Welding Systems Web site: climaxportable.com
Worldwide Phone:
1.503.538.2185 N. America Toll-Free: 1.800.333.8311 Fax: 1.503.538.7600 E-mail: [email protected]
page 2
SPECIFICATIONS
All dimensions should be considered reference. Contact your Climax Representative for precision dimensions. Specifications are subject to change without notice. There are no systems or components
on this machine that are capable of producing hazardous EMC, UV or other radiation hazards. The machine does not use lasers nor does it create hazardous materials such as gasses or dust.
Machine Performance Ranges
ID: Mounting range 20 - 50 inches 508.0 - 1270.0 mm
Facing diameter range 20 - 50 inches 508.0 - 1270.0 mm
Grinding diameter range 22 - 50 inches 558.8 - 1270.0 mm
Swing diameter @ minimum 40 inches 1016.0 mm
with feedbox on end of arm
Radial tool slide travel 12 inches 304.8 mm
Axial tool head travel 4 inches 101.6 mm
Depth required inside bore for ID chuck 2.75 ± 0.25 inches 69.9 ± 6.4 mm
(± 0.25 inches (± 6.4 mm) is travel of leveling foot)
Feed Rate 0.002 - 0.035 in/rev 0.051 - 0.889 mm/rev
OD: Mounting range * 42 - 57.1 inches 1066.8 - 1450.3 mm
Facing diameter range 20 - 50 inches 508.0 - 1270.0 mm
Grinding diameter range (w/ feed box) 22 - 43 inches 558.8 - 1092.2 mm
Grinding diameter range (w/o feed box) 22 - 48 inches 558.8 - 1219.2 mm
Refer to ID for specifications not listed
Rotational Drive System
Drive type Pneumatic or hydraulic drive with
pinion and internal ring gear
Pinion gear to ring gear reduction 5.1: 1
Single point turning speed range:
Pneumatic 7 - 29 RPM
Hydraulic (based on motor choice) 3.5 - 36 RPM
Grinding speed ranges (with reducer):
Pneumatic 0.006 - 0.25 RPM
(rapid only, not in cut) (58 ipm @ 72 inch dia.) (1473.2 mm/min @ 1828.8 mm dia.)
Hydraulic (based on motor choice) 0.011 - 0.75 RPM
Power input requirements
Pneumatic - 3.5 Hp (2.6 kW) 50 ft³/min @ 90 psi 1.53 m³/min @ 620 kPa
Hydraulic 10 gpm @1200 psi 37.9 L/min @ 8273 kPa
Measures
For machine dimensions, please refer to dimensional drawings
ID machine weight, approximate
735 lbs 333.4 kg
OD machine weight, approximate 925 lbs 419.6 kg
ID Crate dimensions (WxDxH)
Wood, approx.
62.5 x 28 x 27.5 in 1588 x 711 x 699 mm
Metal, approx. 60.2 x 25 x 28.5 in 1529 x 635 x 724 mm
OD crate dimensions (WxDxH)
Wood, approx.
40 x 38.5 x 20 in 1016 x 978 x 508 mm
Metal, approx. 46.5 x 25.3 x 18.3 in 1181 x 643 x 465 mm
Testing Data
Flatness at 50 inch (1270 mm) diameter: .0042 inches (.11 mm)
On a dedicated fixture made of A-36 steel in a controlled environment with single point machine, after warm-up.
* OD mount minimum arm swing is 40 inches (1016 mm) diameter. An additional customer supplied structure will be required to chuck below the minimum swing diameter