Atec Agilent-8722ES - Manual (Page 15)

19
Agilent 8719ET, 8720ET, and 8722ET
Description Code
Frequency
Range
8719ET 0.05 to 13.51 GHz S
8720ET 0.05 to 20.05 GHz S
8722ET 0.05 to 40.05 GHz S
Accuracy (at 23° C ±3° C) ±10 ppm S
Stability
0° to 55° C ±7.5 ppm C
Option 1D5 ±0.05 ppm C
Per year (aging) ±3 ppm C
Option 1D5 ±0.5 ppm C
Resolution 1 Hz S
System
Maximum input level
+5 dBm transmission S
+10 dBm reflection
S
Damage level (test port) 27 dBm or 0V dc C
Trace noise 2
Magnitude (RMS of peak-to-peak value)
0.05 to 13.5 GHz <0.03 dB C
13.5 to 20 GHz <0.04 dB C
20 to 40 GHz <0.15 dB C
Phase (RMS of peak-to-peak value)
0.05 to 13.5 GHz <0.3° C
13.5 to 20 GHz <0.4° C
20 to 40 GHz <1.5° C
Spectral purity
Harmonics at maximum output level
<–15 dBc C
Phase noise
to 60 kHz from carrier at 2 GHz <–55 dBc T
to 60 kHz from carrier at 20 GHz <–35 dBc T
Nonharmonic spurious signals
at 100 kHz offset <–40 dBc T
at 200 kHz offset <–45 dBc T
at >200 kHz offset <–65 dBc T
Description Code
Power
Power range
8719ET/8720ET 20 dB C
8722ET
0.05 to 20 GHz 15 dB C
20 to 40 GHz 10 dB C
Power range (Option 004)
8719ET/8720ET 75 dB C
8722ET
0.05 to 20 GHz 70 dB C
20 to 40 GHz 65 dB C
Maximum output power
8719ET/8720ET +10 dBm C
8722ET
0.05 to 20 GHz 0 dBm C
20 to 40 GHz –5 dBm C
Resolution 0.01 dB S
Level accuracy (at 5 dB below maximum output power)
8719ET/8720ET ±2 dB S
8722ET ±3 dB S
Power sweep range
8719ET/8720ET 20 dB S
8719ET/8720ET 30 dB T
8722ET 0.05 to 20 GHz 15 dB S
8722ET 0.05 to 20 GHz 25 dB T
8722ET 20 to 40 GHz 10 dB S
8722ET 20 to 40 GHz 20 dB T
Power linearity
–5 dB from reference:
8719ET/8720ET ±0.35 S
8722ET 0.05 to 20 GHz ±0.35 S
8722ET 20 to 40 GHz ±0.60 S
+5 dB from reference:
8719ET/8720ET ±0.35 S
8722ET 0.05 to 20 GHz ±0.35 S
8722ET 20 to 40 GHz N/A
–10 dB from reference:
8719ET/8720ET/8722ET ±0.60 S
+10 dB from reference:
8719ET/8720ET ±1.0 S
8722ET N/A
Test reference power levels:
8719ET/8720ET (standard, Option 004) 0 dBm S
8722 ET (standard, Option 004) –5 dBm S
Frequency range (GHz)
Description 0.05 to 0.84 0.84 to 2 2 to 8 8 to 20 20 to 40 Code
System
Dynamic range
3
8719ET/8720ET (standard, Options 004) 102 dB 104 dB 104 dB 104 dB S
8722D (standard 4 , Option 400) 98 dB 102 dB 102 dB 100 dB 89 dB S
Receiver 0.1 dB compression input level 13 dBm 10 dBm 10 dBm 10 dBm 10 dBm T
Codes
(S) Specification: warranted performance. Specifications include guardbands
to account for expected statistical performance distribution, measurement
uncertainties, and changes in performance due to environmental conditions.
(C) Characteristic: a performance parameter that the product is expected to meet
before it leaves the factory, but that is not verified in the field and is not covered
by the warranty. A characteristic includes the same guardbands as a specification.
(T) Typical (typ.): expected performance of an average unit which does not include
guardbands. It is not covered by the product warranty.
(N)Nominal (nom.): a general, descriptive term that does not imply a level of
performance. It is not covered by the product warranty.
1. Does not apply to 8722ET.
2. Trace noise is defined as variation of a high signal level trace due to noise. The
value given represents a noise variation that is the RMS of the peak-to-peak value
as measured in a 3 kHz IF bandwidth in the fast sweep mode (STEP SWP OFF).
3. The dynamic range specifications apply to transmission measurements using
10 Hz IF BW and response and isolation correction or full two-port correction.
Dynamic range is limited by the maximum test port power and the receiver’s
noise floor.
4. With 85133E flexible cable on test port.