Asus NCCH-DLE - Manual (Page 47)

A S U S N C C H - D L E A S U S N C C H - D L E A S U S N C C H - D L E A S U S N C C H - D L E A S U S N C C H - D L E 2 - 2 7 2 - 2 7 2 - 2 7 2 - 2 7 2 - 2 7
2 . 2 . 2 . 2 . 2 . S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 ) S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 ) S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 ) S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 ) S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 )
These next generation connectors support the thin Serial ATA cables
for Serial ATA hard disks. The current Serial ATA interface allows up
to 150 MB/s data transfer rate, faster than the standard parallel ATA
with 133 MB/s (Ultra ATA/133).
If you installed Serial ATA hard disks, you may create a RAID 0/RAID 1
configuration using the RAID feature of the Intel
® 6300ESB ICH. Refer
to page 4-19 for the SATA configuration.
NCCH-DLE
®
SATA2
GND
RSA
T A_TXP2
RSA
T A_TXN2
GND
RSA
T A_RXN2
RSA
T
A_RXP2
GND
SATA1
GND
RSA
T A_TXP1
RSA
T A_TXN1
GND
RSA
T
A_RXN1
RSA
T A_RXP1
GND
NCCH-DLE SATA connectors
3 . 3 . 3 . 3 . 3 . U S B c o n n e c t o r ( 1 0 - 1 p i n P 1 , P 2 ) U S B c o n n e c t o r ( 1 0 - 1 p i n P 1 , P 2 ) U S B c o n n e c t o r ( 1 0 - 1 p i n P 1 , P 2 ) U S B c o n n e c t o r ( 1 0 - 1 p i n P 1 , P 2 ) U S B c o n n e c t o r ( 1 0 - 1 p i n P 1 , P 2 )
These connectors are for USB 2.0 ports. Connect the 4-port USB
module cables to these connectors, then install the module to the
opening at the front of the system chassis. The USB connectors
comply with USB 2.0 specification that supports up to 480 Mbps
connection speed.
NCCH-DLE
®
NCCH-DLE USB 2.0 connectors
P1 P2
NC
GND
USB_P8+ USB_P8-
USB+5V
GND USB_P7+ USB_P7- USB+5V
1
NC
GND
USB_P6+ USB_P6-
USB+5V
GND USB_P5+ USB_P5- USB+5V
1
The connector P1 is for front USB ports 5 and 6; P2 is for front USB
ports 7 and 8.