Texas Instruments TMS320F2802 User Manual
Data manual, Digital signal processors
TMS320F2809, TMS320F2808, TMS320F2806
TMS320F2802, TMS320F2801, TMS320C2802
TMS320C2801, TMS320F28016, TMS320F28015
Digital Signal Processors
Data Manual
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Literature Number: SPRS230N
October 2003 – Revised May 2012
This manual is related to the following products:
Table of contents
Document Outline
- Table of Contents
- 1 F280x, F2801x, C280x DSPs
- 2 Introduction
- 3 Functional Overview
- 3.1 Memory Maps
- 3.2 Brief Descriptions
- 3.2.1 C28x CPU
- 3.2.2 Memory Bus (Harvard Bus Architecture)
- 3.2.3 Peripheral Bus
- 3.2.4 Real-Time JTAG and Analysis
- 3.2.5 Flash
- 3.2.6 ROM
- 3.2.7 M0, M1 SARAMs
- 3.2.8 L0, L1, H0 SARAMs
- 3.2.9 Boot ROM
- 3.2.10 Security
- 3.2.11 Peripheral Interrupt Expansion (PIE) Block
- 3.2.12 External Interrupts (XINT1, XINT2, XNMI)
- 3.2.13 Oscillator and PLL
- 3.2.14 Watchdog
- 3.2.15 Peripheral Clocking
- 3.2.16 Low-Power Modes
- 3.2.17 Peripheral Frames 0, 1, 2 (PFn)
- 3.2.18 General-Purpose Input/Output (GPIO) Multiplexer
- 3.2.19 32-Bit CPU-Timers (0, 1, 2)
- 3.2.20 Control Peripherals
- 3.2.21 Serial Port Peripherals
- 3.3 Register Map
- 3.4 Device Emulation Registers
- 3.5 Interrupts
- 3.6 System Control
- 3.7 Low-Power Modes Block
- 4 Peripherals
- 4.1 32-Bit CPU-Timers 0/1/2
- 4.2 Enhanced PWM Modules (ePWM1/2/3/4/5/6)
- 4.3 Hi-Resolution PWM (HRPWM)
- 4.4 Enhanced CAP Modules (eCAP1/2/3/4)
- 4.5 Enhanced QEP Modules (eQEP1/2)
- 4.6 Enhanced Analog-to-Digital Converter (ADC) Module
- 4.7 Enhanced Controller Area Network (eCAN) Modules (eCAN-A and eCAN-B)
- 4.8 Serial Communications Interface (SCI) Modules (SCI-A, SCI-B)
- 4.9 Serial Peripheral Interface (SPI) Modules (SPI-A, SPI-B, SPI-C, SPI-D)
- 4.10 Inter-Integrated Circuit (I2C)
- 4.11 GPIO MUX
- 5 Device Support
- 6 Electrical Specifications
- 6.1 Absolute Maximum Ratings
- 6.2 Recommended Operating Conditions
- 6.3 Electrical Characteristics
- 6.4 Current Consumption
- 6.5 Emulator Connection Without Signal Buffering for the DSP
- 6.6 Timing Parameter Symbology
- 6.7 Clock Requirements and Characteristics
- 6.8 Power Sequencing
- 6.9 General-Purpose Input/Output (GPIO)
- 6.10 Enhanced Control Peripherals
- 6.11 Detailed Descriptions
- 6.12 Flash Timing
- 6.13 ROM Timing (C280x only)
- 7 Migrating From F280x Devices to C280x Devices
- 8 Revision History
- 9 Mechanical Data