Advanced setup —continued – Onkyo 29344937 User Manual
Page 69
69
LPFofLFE
80 Hz, 90 Hz, 100 Hz (default), 120 Hz
(Low-Pass Filter for the LFE Channel)
This setting is not set automatically by the Audyssey 2EQ™ Room Correction and Speaker Setup function
(see page 46).
With this setting, you can specify the cutoff frequency of the LFE channel’s low-pass filter (LPF), which can
be used to filter out unwanted hum. The LPF only applies to sources that use the LFE channel.
DoubleBass
*9
This setting is not set automatically by the Audyssey 2EQ Room Correction and Speaker Setup function
(see page 46).
With the Double Bass function, you can boost bass output by feeding bass sounds from the front left, right, and
center to the subwoofer.
On: Double Bass function on (default).
Off: Double Bass function off.
Notes:
*1 If the “Subwoofer” setting is set to “No”, the “Front” setting is fixed at “FullBand”.
*2 If the “Front” setting is set to anything other than “FullBand”, “FullBand” cannot be selected here.
*3 If the “Surr” setting is set to “None”, this setting cannot be selected.
*4 If the “Surr” setting is set to anything other than “FullBand”, “FullBand” cannot be selected here.
*5 If the “Sp Type” setting is set to “Bi-Amp” (page 44), or Powered Zone 2 is being used (page 81), this setting cannot be selected.
*6 If the “SB/FH” setting is set to “SurrBack” (page 44), this setting cannot be selected.
*7 If the “SB/FH” setting is set to “FrontHigh” (page 44), this setting cannot be selected.
*8 If the “SurrBk” Setting is set to “None” (page 68), this setting cannot be selected.
*9 This function can be set only if the “Subwoofer” setting is set to “Yes”, and the “Front” setting is set to “FullBand”.
2-3. Sp Distance (Speaker Distance)
These settings are set automatically by the Audyssey 2EQ Room Correction and Speaker Setup function (see page 46).
With these settings, you can specify the distance from each speaker to the listening position.
Measure and make a note of the distance from each speaker to the listening position.
Notes:
• Speakers that you set to “No” or “None” in the “2-2. Sp Config (Speaker Configuration)” (page 68) cannot be
selected.
• The speaker distance setting cannot be changed while a pair of headphones is connected.
• The Center, Subwoofer and Front High distances can be set up to 5 ft. (1.5 m) more or less than the Left distance.
For example, if the Left distance is set to 20 ft. (6 m), the Center, Subwoofer, Front High Left and Front High Right
distances can be set between 15 and 25 ft. (4.5 and 7.5 m).
• The Surround and Surround Back distances can be set up to 5 ft. (1.5 m) more or 15 ft. (4.5 m) less than the Left
distance. For example, if the Left distance is set to 20 ft. (6 m), the Surr Right, Surr Left, Surr Back R, and Surr Back
L distances can be set between 5 and 25 ft. (1.5 and 7.5 m).
Unit
feet: Distances can be set in feet. Range: 1 to 30 feet in 1-foot steps.
meters: Distances can be set in meters. Range: 0.3 to 9 meters in 0.3-meter steps.
Left, FrontH L, Center, FrontH R, Right, Surr R, SurrBk R,
SurrBk L, Surr L, Subwfr
Specify the distance from the each speaker to your listening position.