Roland CDX-1 - Manual (Page 248)

20
Mastering Tools parameter list
The Mastering Tools is compressor that splits sounds into different frequency band to unify their volumes.
Parameter (full name) Setting Function
● EQ (Equalizer): A 4-band equalizer.
Effect On/Off (Effect On/Off) OFF, ON This parameter turns the equalizer effect on/off.
Input Gain (Input Gain) -24–+12 dB This parameter sets the overall volume before passing through the equalizer.
Low Type (Low Type) SHELV, PEAKING This parameter sets the type of the low frequency band equalizer
(Shelving type or peaking type).
Low Gain (Low Gain) -12–+12 dB This parameter sets the gain (amount of boost or cut) for the bass
equalizer.
Low Freq (Low Frequency) 20 Hz–2.00 kHz This parameter sets the central frequency for the low equalizer.
Low Q (Low Q) *1 0.3–16.0 This parameter sets the range of change in gain for the frequency set by
“Low Freq.” A larger value results in a narrower range of change.
Low-Mid Gain (Low Middle Gain) -12–+12 dB This parameter sets the gain (amount of boost or cut) for the low-midrange
equalizer.
Low-Mid Freq (Low Middle Frequency) 20 Hz–8.00 kHz This parameter sets the central frequency for the low-midrange equalizer.
Low-Mid Q (Low Middle Q) 0.3–16.0 This parameter sets the range of change in gain for the frequency set by
“Low-Mid Freq.” A larger value results in a narrower range of change.
High-Mid Gain (High Middle Gain) -12–+12 dB This parameter sets the gain (amount of boost or cut) for the high-midrange
equalizer.
High-Mid Freq (High Middle Frequency) 20 Hz–8.00 kHz This parameter sets the central frequency for the high-midrange equalizer.
High-Mid Q (High Middle Q) 0.3–16.0 This parameter sets the range of change in gain for the frequency set by
“High-Mid Freq.” A larger value results in a narrower range of change.
High Type (High Type) SHELV, PEAKING This parameter sets the type of the High frequency band equalizer
(Shelving type or peaking type).
High Gain (High Gain) -12–+12 dB This parameter sets the gain (amount of boost or cut) for the treble
equalizer.
High Freq (High Frequency) 1.40–2.00 kHz This parameter sets the central frequency for the high equalizer.
High Q (High Q) *1 0.3–16.0 This parameter sets the range of change in gain for the frequency set by
“High Freq.” A larger value results in a narrower range of change.
Output Level (Output Level) -24–+12 dB This parameter adjusts the volume after the equalizer stage.
● B CUT (Bass Cut Filter):
Effect On/Off (Effect On/Off) OFF, ON This parameter turns the bass cut filter effect on/off.
Bass Cut Freq (Bass Cut Frequency) THRU, 20 Hz–2.00 kHz This parameter sets the frequency for cutting off undesired low frequency
band sounds such as pop noise.
● ENH (Enhancer): This effect enhances the definition of the sound, and pushes it to the forefront.
Effect On/Off (Effect On/Off) OFF, ON This parameter turns the enhancer effect on/off.
Sensitivity (Sensitivity) 0–100 Adjusts the manner in which the enhancer will be applied relative to the
input signals.
Enhancer Freq (Enhancer Frequency) 1.00 –10.0 kHz Adjusts the frequency at which the enhancer effect will begin to be applied.
The effect will be made apparent in the frequencies above the frequency
set here.
Mix Level (Mix Level) -24–+12 dB Adjusts the amount of phase-shifted sound of the range set by “Frequency”
that is to be mixed with the input.
Compressor
Bass Cut
Filter
Enhancer Equalizer Input Expander
Mixer Limiter Output
Input
Expander Compressor
High Freq
Mid Freq
Low Freq
High Freq
Mid Freq
Low Freq
Mixer
* Below shows the signal form "INPUT" to "MIXER."