Roland RD-700 - Manual (Page 119)

119
Effect/Parameter List
Appendices
High Gain
Adjust the high frequency gain (amount of boost or cut).
Positive (+) settings will emphasize (boost) the high frequency
range.
Balance (Effect Balance) #
Sets the volume balance between the direct sound and the effect
sound.
With a setting of D100:0W only the direct sound will be output,
and with a setting of D0:100W only the effect sound will be
output.
Level (Output Level)
Adjust the output level.
48: 3D DELAY
This applies a 3D effect to the delay sound. The delay sound
will be positioned 90 degrees left and 90 degrees right.
Delay C (Delay Time Center)
Adjust the delay time from the direct sound until the center
delay sound is heard.
Delay L (Delay Time Left)
Adjust the delay time from the direct sound until the left delay
sound is heard.
Delay R (Delay Time Right)
Adjust the delay time from the direct sound until the right delay
sound is heard.
➔
Delay C, Delay L and Delay R parameters can be set as a note-
value of a tempo. In this case, specify the value of the desired
note.
Feedback #
Adjust the proportion (%) of the delay sound that is to be
returned to the input. Positive (+) settings will return the signal
to the input with the original phase, while negative (-) settings
produce an inverted phase.
Level C (Level Center)
Adjust the volume of the center delay sound.
Level L (Level Left)
Adjust the volume of the left delay sound.
Level R (Level Right)
Adjust the volume of the right delay sound.
HF Damp
Adjust the frequency above which delayed sound fed back to
the delay input will be cut.
If you do not want to cut the high frequencies of the feedback,
set this parameter to BYPASS.
Out (Output Mode)
Adjust the method that will be used to hear the output sound.
The optimal 3D effect will be achieved if you select SPEAKER
when using speakers, or PHONES when using headphones.
Low Gain
Adjust the low frequency gain (amount of boost or cut).
Positive (+) settings will emphasize (boost) the low frequency
range.
High Gain
Adjust the high frequency gain (amount of boost or cut).
Positive (+) settings will emphasize (boost) the high frequency
range.
Balance (Effect Balance) #
Sets the volume balance between the direct sound and the effect
sound.
With a setting of D100:0W only the direct sound will be output,
and with a setting of D0:100W only the effect sound will be
output.
Level (Output Level)
Adjust the output level.
49: 3V PCH SHIFT (3 Voice Pitch Shifter)
A Pitch Shifter shifts the pitch of the direct sound. This 3-voice
pitch shifter has three pitch shifters, and can add three pitch
shifted sounds to the direct sound.
Coarse 1:2:3 (Coarse Pitch 1:2:3)
Specify the pitch in semitones for pitch shift 1–3.
Fine 1:2:3 (Fine Pitch 1:2:3)
Make fine adjustments to the pitch of the pitch shift 1–3 in 2-
cent steps.
PreDelay1:2:3 (Pre Delay Time 1:2:3)
Specify the time delay from the direct sound until the pitch shift
1–3 sound is heard.
Feedback1:2:3 (Feedback Level 1:2:3)
Adjust the proportion (%) of the pitch shift 1–3 sound that is fed
back into the effect.
Pan 1:2:3 (Output Pan 1:2:3)
Specify the stereo location of the pitch shift 1–3 sound. L64 is far
left, 0 is center, and 63R is far right.
Level 1:2:3 (Level 1:2:3)
Specify the volume of the pitch shift 1–3.
Mode (Pitch Shifter Mode)
Higher settings of this parameter will result in slower response,
but steadier pitch.
Balance (Effect Balance)
Sets the volume balance between the direct sound and the effect
sound.
With a setting of D100:0W only the direct sound will be output,
and with a setting of D0:100W the effect sound will be output.
Level (Output Level)
Specifies the output volume.
50: LOFI COMPRESS
This is an effect that intentionally degrades the sound quality.
Type (LoFi Type)
Lowers the audio quality. The audio quality will worsen as this
setting is increased.
RD-700_e.book 119 ページ ２００３年１０月２３日 木曜日 午後４時５９分