Nortel Networks NN43001-318 User Manual
Nortel Networks Hardware
Table of contents
Document Outline
- About this document
- Preparing for installation
- Installing ISDN BRI hardware
- Preparing the system
- Configuring ISDN BRI hardware
- Testing ISDN BRI functions
- Generating traffic reports
- Figures
- Figure 1 NT8D35 Network module (Large System)
- Figure 2 NT8D37 IPE module (Large System)
- Figure 3 NT4N41 Core/Network module (Large System)
- Figure 4 Module cover locking latches
- Figure 5 Connect the ISDN BRI terminals to the Large System
- Figure 6 Connect the system to the MDF
- Figure 7 Cross-connect the SILC port to the office wiring
- Figure 8 Cross-connect the UILC port to the office wiring
- Figure 9 Connect the ISDN BRI terminal to the S/T interface
- Figure 10 Connect the ISDN BRI network termination (NT1) to the U interface
- Figure 11 Clock reference cable connection
- Figure 12 Connect the network termination to the U interface and to the S/T interface (in TE mode)
- Figure 13 ISDN BRI acceptance testing setup for terminals
- Figure 14 ISDN BRI acceptance testing setup for trunking - Local Exchange connectivity
- Figure 15 ISDN BRI acceptance testing setup for trunking - TIE trunk connectivity
- Figure 16 SILC line power options
- Figure 17 Jumper plug settings for normal power on the TX and RX leads
- Figure 18 Jumper plug settings for reverse power on the TX and RX leads
- Figure 19 Connecting ISDN BRI terminals to the system
- Figure 20 Cable connectors in main cabinet
- Figure 21 Cable connectors in the expansion cabinet
- Figure 22 Cable connectors in the second expansion cabinet
- Figure 23 Back of MG 1000S cable connectors
- Figure 24 SILC port designation label at the cross-connect terminal
- Figure 25 UILC port designation label at the cross-connect terminal
- Figure 26 Cross-connecting a SILC port to the office wiring
- Figure 27 Cross-connecting a UILC port to the office wiring
- Figure 28 Connecting the ISDN BRI terminal to the S/T interface
- Figure 29 Connecting the ISDN network terminator to the U interface
- Figure 30 Cross-connecting an SILC port
- Figure 31 Cross-connecting a UILC port
- Figure 32 Connecting the ISDN network terminator to the U interface and to the S/T interface (in TE mode)
- Figure 33 Network traffic report
- Tables
- Table 1 Meridian 1 systems to CS 1000M systems
- Table 2 ISDN BRI card location
- Table 3 SILC port designations at the MDF: NT8D37 IPE module (16-cable configuration)
- Table 4 UILC port designation labels at the MDF: NT8D37 IPE module (16-cable configuration)
- Table 5 NT8D37 IPE moduleSILC and UILC pair-terminations for connectors A, E, K, R (12-cable configuration)
- Table 6 NT8D37 IPE moduleSILC and UILC pair-terminations for connectors B, F, L, S (12-cable configuration)
- Table 7 NT8D37 IPE moduleSILC and UILC pair-terminations for connectors C, G, M, T (12-cable configuration)
- Table 8 ISDN BRI clock reference tables
- Table 9 Clocks as differential pairs
- Table 10 Card location form: NT8D37 IPE module (16-cable configuration)
- Table 11 Card location form: NT8D37 IPE module (12-cable configuration)
- Table 12 Hardware requirements for line and packet data applications
- Table 13 Hardware requirements for ISDN BRI trunking
- Table 14 Correct responses to LOOP and MISP prompts in LD 27
- Table 15 Small System shelf slot assignments for ISDN BRI cards
- Table 16 SILC and UILC port assignments connectors at cross-connect terminal
- Table 17 S/T interface connector specification
- Table 18 U interface connector specification
- Table 19 M5317TDX terminal error codes
- Procedures
- Procedure 1 Selecting the card slots
- Procedure 2 Remove the module cover for card installation
- Procedure 3 Installing the MISP
- Procedure 4 Removing the MISP
- Procedure 5 Installing the BRSC, SILC, and UILC
- Procedure 6 Remove the BRSC, SILC, and UILC
- Procedure 7 Connecting ISDN BRI terminals to the system
- Procedure 8 Connect the modules to the MDF
- Procedure 9 Cross-connecting SILC and/or UILC ports to the building wiring
- Procedure 10 Connecting the ISDN BRI terminals to the DSL
- Procedure 11 Providing clock referencing on the SILC
- Procedure 12 Connecting clock reference cables
- Procedure 13 Performing acceptance testing
- Procedure 14 Selecting the card slots
- Procedure 15 Installing the MISP
- Procedure 16 Removing the MISP
- Procedure 17 Installing the SILCs and UILCs
- Procedure 18 Removing the SILC and UILC
- Procedure 19 Installing the PRI hardware
- Procedure 20 Connecting system cables to the cross-connect terminal
- Procedure 21 Cross-connecting the DSLs at the cross-connect terminal
- Procedure 22 Connecting the terminating resistor to the SILC DSL
- Procedure 23 Connecting the ISDN BRI terminals to the DSL
- Procedure 24 Initializing a Nortel Networks M5317TDX terminal
- Procedure 25 Connecting the system cables to the cross-connect terminal
- Procedure 26 Cross-connecting DSLs at the cross-connect terminal
- Procedure 27 Performing a call hold test
- Procedure 28 Perform a Call Waiting test
- Procedure 29 Performing a Call Forward No Answer test
- Procedure 30 Perform a Calling Line Identification Presentation test
- Procedure 31 Perform an ISDN BRI Conference test
- Procedure 32 Perform a Call Join test on Conference
- Procedure 33 Perform a hunting test
- Procedure 34 Perform an ISDN BRI NI-1 Call Forward All Calls test
- Procedure 35 Perform an ISDN BRI ETSI Call Forwarding Unconditional test
- Procedure 36 Perform a circuit-switched data call test
- Procedure 37 Perform a B-channel packet data transmission test using an external packet handler
- Procedure 38 Perform a D-channel packet data transmission test using an external packet handler
- Procedure 39 Perform a D-channel Switched Virtual Circuit packet data transmission test using an MPH
- Procedure 40 Perform a B-channel Switched Virtual Circuit packet data transmission test using an MPH
- Procedure 41 Perform procedure to test an ISDN BRI trunk DSL