MITSUBISHI ELECTRIC WD-65736 - Manual (Page 59)

6. NetCommand IR Control (736 and 835 Series TVs) 59
57
BVEJPWJEFP
*ODPNJOH$PBYJBM$BCMF
GSPN"/5"/5
"73FDFJWFS
%7%BVEJP
JOQVU
57BVEJPJOQVU
57BVEJP
PVU
BVEJPPVUQVUGSPN
57 EJHJUBMPSBOBMPH
WJEFP
BOBMPHBVEJP
7$3XJUI
"OBMPH"VEJP0VUQVU
Setup 1: A/V receiver audio from the TV’s digital or
analog audio output (
DIGITAL AUDIO OUTPUT or AVR
AUDIO OUTPUT)
Under 1. Learn, highlight Input1.
In this example, the IR code for the A/V receiver’s
TV Audio input will be “learned” as Input 1.
Press 2. ENTER on the TV’s remote control.
While the text 3. Input1 is flashing, press and hold the
TV INPUT key on the A/V receiver’s remote control.
When a check appears next to 4. Input 1, release the
TV INPUT key.
If the text stops flashing before the check mark t
appears, repeat this step.
To erase the IR code just “learned,” press
t CANCEL
while the name is highlighted.
Press 5. once to highlight TV Audio (TV audio
output) in the Assign Input1 column. The triangular
marker is always next to the assigned sound source.
Press 6. EXIT if finished or continue with setup for
another TV audio source.
Completed NetCommand setup described for
controlling A/V receiver switching to the A/V receiver’s
audio input from the TV’s
AUDIO OUTPUT.
Setup 2: Automatic A/V Receiver Switching for a
Surround Sound Device
Use this setup to send digital surround sound directly
from a device to an A/V receiver.
Under 1. Learn, highlight Input2.
In this example, the IR code for the A/V receiver’s
DVD Audio input will be “learned” as Input2.
Press 2. ENTER on the TV’s remote control.
57
"73FDFJWFS
%7%BVEJP
JOQVU
WJEFP
EJHJUBMTVSSPVOETPVOE %7%1MBZFS
XJUI
%JHJUBM
4VSSPVOE
4PVOE
Setup 2: A/V receiver audio from a device providing
surround sound directly to the A/V receiver
Completed NetCommand setup described for
controlling A/V receiver switching to an A/V receiver
input “learned” as
Input2.
While the text 3. Input2 is flashing, press and hold the
DVD INPUT key on the A/V receiver’s remote control.
When a check appears next to 4. Input2, release the
DVD INPUT key.
t *GUIFUFYUTUPQTGMBTIJOHCFGPSFUIFDIFDLNBSL
appears, repeat this step.
t 5PFSBTFUIF*3DPEFKVTUiMFBSOFE
wQSFTTCANCEL
while the name is highlighted.
Press 5. once to automatically move the highlight to
the Assign Input2 column.
Use 6. to highlight DVD in the list of devices
recognized by the TV. The triangular marker always
shows the assigned sound source.
Press 7. EXIT if finished or continue for additional TV
sources.
Setting Up NetCommand Control of
an A/V Receiver, continued
IMPORTANT
All audio from what you are watching on the
TV is always available from both the TV’s AVR
AUDIO OUTPUT and DIGITAL AUDIO OUTPUT
jacks.
To use the digital surround sound capabilities
of your A/V receiver however, you must connect
your DVD player, satellite receiver, or cable box
directly to the A/V receiver, as surround sound
may not be available from the TV’s audio output.