MITSUBISHI ELECTRIC WD-65736 - Manual (Page 27)

4. TV Operation and Features 27
21. MENU: Displays the main TV menu. When a sub-
menu is open, backs up one menu level.
22. EXIT: Closes TV on-screen menus/displays.
23. F1–F4
For devices under NetCommand control:
Perform NetCommand “Learning” to assign your
choice of functions to the F1–F4 keys.
For devices operating independently of
NetCommand: The F1–F4 keys work like the A,
B, C, D buttons on some cable boxes, satellite
receivers, and DVD players. Program the remote
control for your equipment and test the keys. See
Appendix C, “Programming the Remote Control.”
25. (PAUSE): Freezes a broadcast TV picture from an
antenna source, cable box, or satellite receiver (if
key has not been reassigned for NetCommand use).
Record/Playback Keys
Use any of these methods to enable the recording and
playback commands of the TV’s remote control:
t 1SPHSBNUIFSFNPUFDPOUSPMGPSZPVS%73
7$3
PS
DVD player/recorder and set the slide switch to VCR,
DVD, CABLE/SAT, or AUDIO as appropriate.
t $IFDL)%.*EFWJDFTGPSDPNQBUJCJMJUZXJUIUIF57T
NetCommand for HDMI feature (see “NetCommand
for HDMI Devices” on the next page).
t BOETFSJFTNPEFMTPOMZ1FSGPSN/FU$PN-
mand IR “learning” for the device.
24. (RECORD): Records with a VCR or DVR.
25. (PAUSE): Pauses a VCR, DVR, or DVD. See
above for use during TV viewing.
26. (STOP): Stops play of a VCR, DVR, or DVD.
27. (REVERSE): Rewinds a VCR. Reverse scans a
DVR or DVD.
28. (PLAY): Plays a VCR, DVR, or DVD.
29. (FORWARD): Fast forwards a VCR. Forward scans
a DVR or DVD.
Remote Control, continued
Care of the Remote Control
Use only alkaline batteries. t
Be within 20 feet of the equipment. t
Do not press two or more buttons at the same time t
unless instructed to do so.
Do not allow unit to get wet or become heated.
t
Avoid dropping on hard surfaces. t
Do not use harsh chemicals to clean. Use only a t
soft, lightly moistened cloth.
Do not mix old and new batteries.
t
Resetting the Remote Control
If the slide switch is set to TV and the TV does not
respond properly, reset the remote control.
Press and hold 1. POWER for several seconds until the
button blinks twice and goes off.
Release the 2. POWER button.
Press keys 3. 0 0 9 3 5 and the POWER button will blink
twice when you finish entering the code. While
entering the code, pause for a moment between
each key press to ensure it is recognized.
Low-Battery Indicator
If you press a key and the POWER key blinks five times,
replace the remote control’s batteries.
Note: To operate other audio/video devices using
the TV’s remote control:
t 4FF"QQFOEJY$
i1SPHSBNNJOHUIF3FNPUF
Control.”
t 'PS)%.*EFWJDFTDPNQBUJCMFXJUIUIF57T/FU-
Command for HDMI feature, see “NetCommand
for HDMI Devices” on the next page.
t BOETFSJFTNPEFMTPOMZ4FFDIBQUFS
“NetCommand IR Control,” for NetCommand IR
“Learning” of device keys.
t 'PSVTFPGTQFDJGJDLFZTXJUI/FU$PNNBOEDPO-
trolled devices, see “Special Operation Methods,”
page 55.