GE GEFanuc Automation Programmable Control Products TCP/IP Ethernet Communications for the Series 90t-70 PLC GFK-1004B User Manual
Page 195

6
6-24
TCP/IP Ethernet Communications User’s Manual – January 1996
GFK-1004B
Table 6-10. Exception Log Event Codes - Continued
ББББББ
ББББББ
ББББББ
Log Event
Code
ББББББББББББББББББББББ
ББББББББББББББББББББББ
ББББББББББББББББББББББ
Possible Cause and Resolution
ББББББ
ББББББ
ББББББ
ББББББ
ББББББ
ББББББ
ББББББ
ББББББ
ББББББ
ББББББ
ББББББ
ББББББ
ББББББ
ББББББ
ББББББ
ББББББ
ББББББ
ББББББ
ББББББ
ББББББ
ББББББ
ББББББ
ББББББ
ББББББ
ББББББ
ББББББ
ББББББ
ББББББ
ББББББ
ББББББ
ББББББ
ББББББ
Event ”12”
TCP events
(Continued)
ББББББББББББББББББББББ
ББББББББББББББББББББББ
ББББББББББББББББББББББ
ББББББББББББББББББББББ
ББББББББББББББББББББББ
ББББББББББББББББББББББ
ББББББББББББББББББББББ
ББББББББББББББББББББББ
ББББББББББББББББББББББ
ББББББББББББББББББББББ
ББББББББББББББББББББББ
ББББББББББББББББББББББ
ББББББББББББББББББББББ
ББББББББББББББББББББББ
ББББББББББББББББББББББ
ББББББББББББББББББББББ
ББББББББББББББББББББББ
ББББББББББББББББББББББ
ББББББББББББББББББББББ
ББББББББББББББББББББББ
ББББББББББББББББББББББ
ББББББББББББББББББББББ
ББББББББББББББББББББББ
ББББББББББББББББББББББ
ББББББББББББББББББББББ
ББББББББББББББББББББББ
ББББББББББББББББББББББ
ББББББББББББББББББББББ
ББББББББББББББББББББББ
ББББББББББББББББББББББ
ББББББББББББББББББББББ
ББББББББББББББББББББББ
18 “Connection to remote node failed; resuming”
Sent RST in tcpacked( ). Entry 3 is the endpoint (TCP connection identifier).
Entry 4
is the TCP state as shown above. Entry 5 is the code field of the
offending packet.
19 “Connection to remote node failed; resuming”
Sent a TCP RST to a remote node aborting a failed TCP connection. This
abort was done due to a mismatch in local and remote connection status.
Entry 3
is the endpoint (TCP connection identifier). Entry 4 is the TCP state:
1 = CLOSED
2 = LISTEN
3 = SYN-SENT
4 = SYN-RECEIVED
5 = ESTABLISHED
6 = FIN-WAIT-1
7 = FIN-WAIT-2
8 = CLOSE-WAIT
9 = LAST-ACK
10 = CLOSING
11 = TIME-WAIT
Entry 5
contains TCP flags.
1a “Connection to remote node failed; resuming”
Sent a TCP RST to a remote node aborting its TCP connection. This abort was
done because the connection was unknown to the local Interface. Entry 3 is
the source TCP port. Entry 4 is the destination TCP port. Entry 5 is the code
field of the offending TCP packet.
1b “Connection to remote node failed; resuming”
Gave up on TCP connection establishment due to exceeding the limit on the
listen queue size.
1c “Connection to remote node failed; resuming”
Closed a connection that has not yet been set up Entry 3 contains the end-
point, and Entry 4 contains the TCP state. This exception may serve to explain
a subsequent event 12, Entry 2 = 1a exception.
ff
(Not reported to PLC Fault Table)
An error has occurred while retrieving program task names, but the software
is unable to clear an entry in the PSM transfer table. Entry 3 is the returned
status code and is significant to developers.