Troubleshooting when the status ok led is on – GE GEFanuc Automation Programmable Control Products TCP/IP Ethernet Communications for the Series 90t-70 PLC GFK-1004B User Manual
Page 180

6
6-9
GFK-1004B
Chapter 6 Troubleshooting
Count
- The Count column contains a repetition count for the event. If events which are
identical occur regularly, they might otherwise flood the log with useless entries.
Instead of recording each repeated event in detail, the log simply keeps the time of the
latest event and a count of the number of repetitions of the repeated event. Log entries
are retained on restart and reloads of the Ethernet Interface.
Entry
- The Entry columns contain detailed information about the event and is
subdivided into 6 entries, Entry 1 - Entry 6.
Troubleshooting When the STATUS OK LED is ON
Sometimes problems can occur even when the STATUS OK LED is ON, indicating
normal operation. In this case, follow the troubleshooting procedure below.
Table 6-7. Troubleshooting with ONLINE LED OFF
ББББББ
ББББББ
LED Indicators
БББББББББББББББББББББ
БББББББББББББББББББББ
Possible Cause and Resolution
ББББББ
ББББББ
ББББББ
The ONLINE
LED is OFF
БББББББББББББББББББББ
БББББББББББББББББББББ
БББББББББББББББББББББ
This indicates that an attempt to send a frame resulted in a local fault indica-
tion. This usually results from a hardware problem. If this occurs follow the
procedure below.
ББББББ
ББББББ
ББББББ
БББББББББББББББББББББ
БББББББББББББББББББББ
БББББББББББББББББББББ
-
Check to be sure the LAN ONLINE Soft Switch is set to “YES”. By
issuing the Soft Switch Station Manager command checking the
Network Online field.
ББББББ
ББББББ
БББББББББББББББББББББ
БББББББББББББББББББББ
-
Check to be sure the drop cable is securely fastened to the controller
board connector and to the transceiver.
ББББББ
ББББББ
ББББББ
БББББББББББББББББББББ
БББББББББББББББББББББ
БББББББББББББББББББББ
-
Make sure the transceiver is securely fastened to the Ethernet
network
trunk
cable.
ББББББ
ББББББ
ББББББ
БББББББББББББББББББББ
БББББББББББББББББББББ
БББББББББББББББББББББ
-
Issue a TALLY L Station Manager. If either the MacErr or the
SQEErr tally is non-zero, the local station may be experiencing an
unstable network. In this case follow the procedure below.
ББББББ
ББББББ
БББББББББББББББББББББ
БББББББББББББББББББББ
If this station is the only one experiencing problems:
ББББББ
ББББББ
БББББББББББББББББББББ
БББББББББББББББББББББ
-
Verify that the SQE jumper is enabled on the transceiver connected
to the Ethernet Interface.
ББББББ
ББББББ
БББББББББББББББББББББ
БББББББББББББББББББББ
-
Re-tighten all transceiver cable connections.
ББББББ
ББББББ
БББББББББББББББББББББ
БББББББББББББББББББББ
-
Make sure the slide lock on the Ethernet Controller board is locked.
ББББББ
ББББББ
БББББББББББББББББББББ
БББББББББББББББББББББ
-
Replace the transceiver cable with a known good cable.
ББББББ
ББББББ
БББББББББББББББББББББ
БББББББББББББББББББББ
-
Verify that the Series 90-70 PLC power supply is properly grounded.
ББББББ
ББББББ
БББББББББББББББББББББ
БББББББББББББББББББББ
-
Make sure that the Ethernet Controller board ground safety wire is
securely fastened.
ББББББ
ББББББ
БББББББББББББББББББББ
БББББББББББББББББББББ
-
Replace the transceiver with a known good transceiver.
ББББББ
ББББББ
ББББББ
БББББББББББББББББББББ
БББББББББББББББББББББ
БББББББББББББББББББББ
If all stations are experiencing the problem, the cable plant is probably
at fault.
ББББББ
ББББББ
БББББББББББББББББББББ
БББББББББББББББББББББ
-
Recertify the cable plant.
ББББББ
ББББББ
БББББББББББББББББББББ
БББББББББББББББББББББ
If the problem still exists, call GE Fanuc Automation for support.