Exception log event error codes – GE GEFanuc Automation Programmable Control Products TCP/IP Ethernet Communications for the Series 90t-70 PLC GFK-1004B User Manual
Page 181

6
6-10
TCP/IP Ethernet Communications User’s Manual – January 1996
GFK-1004B
Table 6-8. Troubleshooting with ONLINE LED ON
БББББББ
БББББББ
LED Indicators
ББББББББББББББББББББББ
ББББББББББББББББББББББ
Possible Cause and Resolution
БББББББ
БББББББ
БББББББ
The ONLINE LED
is ON, but there is
no network activity.
ББББББББББББББББББББББ
ББББББББББББББББББББББ
ББББББББББББББББББББББ
There are several possible causes if a station cannot transfer data on the network.
These causes are described below with the appropriate action to be taken.
БББББББ
БББББББ
ББББББББББББББББББББББ
ББББББББББББББББББББББ
PLC Access Problem
БББББББ
БББББББ
БББББББ
ББББББББББББББББББББББ
ББББББББББББББББББББББ
ББББББББББББББББББББББ
To verify that the Ethernet Interface can access the PLC, issue successive
TALLY C Station Manager commands. If the PlcSweep tally is not increasing,
there are no windows being provided by the PLC.
БББББББ
БББББББ
БББББББ
БББББББ
ББББББББББББББББББББББ
ББББББББББББББББББББББ
ББББББББББББББББББББББ
ББББББББББББББББББББББ
-
If any of the tallies PlcAbt, MyAbt, or Timeout are incrementing,
there may be a hardware problem with the Series 90-70 PLC backplane
interface. Check the PLC Fault Table for entries for the Ethernet
Interface.
БББББББ
БББББББ
ББББББББББББББББББББББ
ББББББББББББББББББББББ
-
Make sure to set the Soft Switch parameter bponline to “YES”.
БББББББ
БББББББ
ББББББББББББББББББББББ
ББББББББББББББББББББББ
-
Replace the digital controller board with a known good board.
Exception Log Event Error Codes
The error codes below appear in the Event column of a log event. To view the log, issue
the LOG command from the Station Manager.
Table 6-9. Exception Log Event Definitions
БББББ
БББББ
Log Event
ББББББББББББББББ
ББББББББББББББББ
Cause
БББББ
БББББ
БББББ
1
ББББББББББББББББ
ББББББББББББББББ
ББББББББББББББББ
Powerup. A log entry of this event will appear every
time the Ethernet Interface is Restarted or powered
up.
БББББ
БББББ
2
ББББББББББББББББ
ББББББББББББББББ
System events.
БББББ
БББББ
8
ББББББББББББББББ
ББББББББББББББББ
PLC driver events.
БББББ
БББББ
b
ББББББББББББББББ
ББББББББББББББББ
Service Agent events.
БББББ
БББББ
c
ББББББББББББББББ
ББББББББББББББББ
LLC events.
БББББ
БББББ
11
ББББББББББББББББ
ББББББББББББББББ
IP events
БББББ
БББББ
12
ББББББББББББББББ
ББББББББББББББББ
TCP events
БББББ
БББББ
16
ББББББББББББББББ
ББББББББББББББББ
ARP events
БББББ
БББББ
18
ББББББББББББББББ
ББББББББББББББББ
ICMP events
БББББ
БББББ
1b
ББББББББББББББББ
ББББББББББББББББ
SRTP Server events
БББББ
1c
ББББББББББББББББ
Channel API events