Date and time, Station manager command syntax – GE GEFanuc Automation Programmable Control Products TCP/IP Ethernet Communications for the Series 90t-70 PLC GFK-1004B User Manual
Page 135

5
5-8
TCP/IP Ethernet Communications User’s Manual – January 1996
GFK-1004B
To list the Monitor commands and Modify commands on the screen, type:
HELP
?
The following table provides a brief description of the Modify commands.
Table 5-2. Modify Commands
ББББББ
ББББББ
Command
БББББББББББББББББ
БББББББББББББББББ
Description
ББББББ
chbps
БББББББББББББББББ
Change serial port data rate
ББББББ
ББББББ
ББББББ
chdate
БББББББББББББББББ
БББББББББББББББББ
БББББББББББББББББ
Change date (Not recommended if PLC CPU is configured
properly.)
ББББББ
ББББББ
chltime
БББББББББББББББББ
БББББББББББББББББ
Change login timeout
ББББББ
ББББББ
chsosw
БББББББББББББББББ
БББББББББББББББББ
Change Soft Switch data (Not recommended .)
ББББББ
ББББББ
chtime
БББББББББББББББББ
БББББББББББББББББ
Change time (Not recommended if PLC CPU is
configured properly.)
ББББББ
ББББББ
clear
БББББББББББББББББ
БББББББББББББББББ
Clear Extended Status buffer, Exception Log,Tallies, or Heap
ББББББ
ББББББ
clsosw
БББББББББББББББББ
БББББББББББББББББ
Clear Soft Switch values on TCP/IP Ethernet Interface (Not
recommended.)
ББББББ
ББББББ
load
БББББББББББББББББ
БББББББББББББББББ
Force TCP/IP Ethernet Interface to be loaded
ББББББ
ББББББ
logout
БББББББББББББББББ
БББББББББББББББББ
Exit modify mode
ББББББ
ББББББ
net
БББББББББББББББББ
БББББББББББББББББ
Disable/Enable node from network
ББББББ
ББББББ
ok
БББББББББББББББББ
БББББББББББББББББ
Turns on STATUS OK LED
ББББББ
ББББББ
ping
БББББББББББББББББ
БББББББББББББББББ
Issues ICMP echo request
ББББББ
rem
БББББББББББББББББ
Send command to remote station
ББББББ
ББББББ
report
БББББББББББББББББ
БББББББББББББББББ
Report test results
ББББББ
ББББББ
repp
БББББББББББББББББ
БББББББББББББББББ
Report ping results
ББББББ
ББББББ
restart
БББББББББББББББББ
БББББББББББББББББ
Restart the TCP/IP Ethernet Interface
ББББББ
ББББББ
stopp
БББББББББББББББББ
БББББББББББББББББ
Stop ping command
ББББББ
ББББББ
stopt
БББББББББББББББББ
БББББББББББББББББ
Stop test command
ББББББ
ББББББ
test
БББББББББББББББББ
БББББББББББББББББ
Send test commands to station(s)
ББББББ
ББББББ
trace
БББББББББББББББББ
БББББББББББББББББ
Turn on specific task trace flags
Date and Time
The Station Manager provides commands to examine the date and time. Any time the
TCP/IP Ethernet Interface is restarted or power to it is cycled, it will attempt to read the
date and time from the PLC CPU. If this fails, the time reverts to midnight and the date
to January 1, 1989; it is only in the case of failure to read date/time from the CPU that
you must set it using the Station Manager. If accurate time stamp information is to be
generated in the Exception Log, the system date and time must be set using the Station
Manager.
Station Manager Command Syntax
The Command Descriptions section which follows provides an alphabetical listing of the
commands. Each entry describes the input and output for each command.
All commands have the format of a command followed by a variable number of argu-
ments separated by spaces. Details about the arguments are discussed with each com-