GE GEFanuc Automation Programmable Control Products TCP/IP Ethernet Communications for the Series 90t-70 PLC GFK-1004B User Manual
Page 139

5
5-12
TCP/IP Ethernet Communications User’s Manual – January 1996
GFK-1004B
PROM/software versions are incompatible, or station MAC address in soft switches does
not match downloaded configuration.
Table 5-4.
Soft Switch Entry Utility Commands
БББББББ
БББББББ
Command
БББББББББББББББББ
БББББББББББББББББ
Restrictions
БББББББ
БББББББ
bps
БББББББББББББББББ
БББББББББББББББББ
БББББББ
БББББББ
chbps
БББББББББББББББББ
БББББББББББББББББ
БББББББ
chdate
БББББББББББББББББ
(Not recommended if the PLC CPU is configured properly.)
БББББББ
БББББББ
chsosw
БББББББББББББББББ
БББББББББББББББББ
(Not recommended if the PLC CPU is configured properly.)
БББББББ
БББББББ
chtime
БББББББББББББББББ
БББББББББББББББББ
(Not recommended if the PLC CPU is configured properly.)
БББББББ
БББББББ
clear
БББББББББББББББББ
БББББББББББББББББ
Limited to clear tally, clear log, and clear heap
БББББББ
БББББББ
clsosw
БББББББББББББББББ
БББББББББББББББББ
(Not recommended if the PLC CPU is configured properly.)
БББББББ
БББББББ
date
БББББББББББББББББ
БББББББББББББББББ
БББББББ
БББББББ
help or ?
БББББББББББББББББ
БББББББББББББББББ
БББББББ
БББББББ
load
БББББББББББББББББ
БББББББББББББББББ
БББББББ
БББББББ
log
БББББББББББББББББ
БББББББББББББББББ
БББББББ
БББББББ
login
БББББББББББББББББ
БББББББББББББББББ
БББББББ
БББББББ
node
БББББББББББББББББ
БББББББББББББББББ
БББББББ
БББББББ
ok
БББББББББББББББББ
БББББББББББББББББ
БББББББ
БББББББ
restart
БББББББББББББББББ
БББББББББББББББББ
БББББББ
show
БББББББББББББББББ
Only task identifiers “b” and “c” are supported
БББББББ
БББББББ
sosw
БББББББББББББББББ
БББББББББББББББББ
БББББББ
БББББББ
stat
БББББББББББББББББ
БББББББББББББББББ
Only task identifiers “b” and “c” are supported
БББББББ
БББББББ
tally
БББББББББББББББББ
БББББББББББББББББ
Only task identifiers “b” and “c” are supported
БББББББ
БББББББ
time
БББББББББББББББББ
БББББББББББББББББ
Monitor Commands are not in italics. Modify Commands are shown in italics.
If the Soft Switch values are not defined or disagree with other evidence, the problem
must be satisfactorily resolved by one or more of the following actions:
1.
Set the MAC address or IP address to the correct value via Logicmaster 90
Configurator.
2.
If not configured via Logicmaster 90, use the CHSOSW Station Manager command
described in this chapter.
3.
Adjust the GSM configuration for the Ethernet Interface.
4.
Download the Ethernet Interface from the GSM.
Other wise, you will be continually placed back into this utility after each restart. For
proper usage of the CHSOSW command, see the CHSOSW command description in this
chapter.
The Soft Switch Entry utility is exited by restarting the Ethernet Interface. This can be
accomplished by entering the RESTART or LOAD commands, pressing the Ethernet In-
terface Restart pushbutton, or by cycling power on the Series 90-70 PLC.