Marantz AV8003 User Manual

Page 95

CONNECTIONS

SETUP

BASIC

OPERA

TION

ADV

ANCED

OPERA

TION

TROUBLESHOOTING

OTHERS

NAMES AND

FUNCTION

REMOTE

CONTROLLER

ENGLISH

BASIC OPERATION

NORMAL MODE

(When operating Marantz AV equipment products)

This remote controller is preset with a total of
12 types of remote codes, including Marantz TV
(television), DVD, VCR (VCR deck), DSS (satellite
broadcasting tuner), TUNER 1, TUNER 2, CD, CD-R,
TAPE (tape deck), AUX1 and AUX2.
Learning is not necessary for Marantz products. You
can use these products without setting any codes.

Press

the

SOURCE button.

For this example, press DVD.
Pressing the SOURCE button once changes
the remote control to the settings for the source
that was pressed.
To change the amplifi er on other source, press
the SOURCE button twice (double-click). The
code is sent, and then the amplifi er source
changes to DVD.

SETTING THE BACK LIGHT

Each time press the buttons, illuminate button 2
seconds.
To turn off back light, press and hold down the SET
and

button until SEND indicator blinks twice.

To turn on it again, press and hold down the SET and

button until SEND indicator blinks twice.

Initial is back light ON.

PRESET MODE

(When operating non-Marantz AV equipment
products)

This remote controller is preset with remote control
codes from AV equipment by other manufacturers.
The preset codes are TV, DVD, CD and DSS.
Settings can be made in one of two ways.
When the preset codes are set, the following codes
are contained in the source button of the remote
controller.

See the attached manufacturer number list for the
preset manufacturers, devices, preset numbers, and
other settings.

Remote control
source name

Corresponding preset
code

Device name

Television

DVD

DVD player

CD player

DSS

SATELLITE

Satellite broadcasting
tuner equipment

Importants:

• Some codes may be not match your equipment.
In this case, you can use LEARN mode to store these

codes.

• The preset codes do not cover full functions.
If you need extra function, use LEARN mode to

store extra function.

• When the batteries are getting weak, the preset

procedure is not successful.

PROGRAMMING WITH THE 4-DIGIT CODE

Press and hold down the SOURCE button (ex

TV) for the appliance which should be controlled
and press SET button until the SEND indicator
blinks twice. Then back light fl ashes.

Press the 4-digit code by numeric keys for

appliance (code table at the end of this book)

When the procedure is successful, the SEND

indicator will blink twice.

Note:

If the indicator did not blink twice, then repeat steps 1
through 2 and try entering the same code again.

SCANNING THE CODE TABLE

Switch on the appliance which should be

controlled.

Press and hold down the SOURCE button for

appliance which should be controlled and press
SET button until the SEND indicator blinking
twice. Then back light fl ashes.

Aim the remote controller at the appliance and

alternately press the CH+ and SOURCE ON
buttons slowly.

Stop when the appliance turns off.

Press

ENTER button once to lock in the code.

When the procedure is successful, the SEND

indicator will blink twice.

CHECKING THE CODE

3.
1.

Press and hold down the SOURCE button for

appliance which should be controlled and press
SET button until the SEND indicator blinking twice
then back light fl ashes.

Press

the

INFO button.

The SEND indicator will blink twice.

To view the code for fi rst digit, press 1 once.

Count the SEND indicator blinks (e.g. 3 blinks =

3) and write down the number.

Note:

If a code digit is “0”, the SEND indicator will not
blink.

Repeat

step

three more times for remaining

digits. Use 2 for the second digit, 3 for the third
digit, and

4 for the fourth digit.

RESETTING THE CODE

Press and hold down the SOURCE button

for appliance which should be controlled and
press SET button until the SEND indicator
blinking twice.

Then back light fl ashes.

Press the below codes to reset.

TV :

1000

DVD

2000

CD :

3000

DSS

4000

The indicator will blink twice.

Note:

After this procedure, the selected SOURCE button is
set initial code.

AV8003_U_Eng.indb 92

08.4.28 10:40:46 AM