Names and function – Marantz AV8003 User Manual

Page 8

CONNECTIONS

NAMES AND

FUNCTION

SETUP

BASIC

OPERA

TION

ADV

ANCED

OPERA

TION

REMOTE

CONTROLLER

TROUBLESHOOTING

OTHERS

ENGLISH

t PURE DIRECT button and indicator

When this button is pressed once, “SOURCE
DIRECT” appears on the FL display. If pressed again,
“PURE DIRECT” appears. After 2 seconds, the FL
display indication goes out.
In the source/pure direct mode, the tone control
circuitry and bass management are bypassed.

Notes:

• The surround mode is automatically switched to

AUTO when the pure direct function is turned on.

• Additionally, speaker configurations are fixed

automatically as follows.

Front SPKR = LARGE

Center SPKR = LARGE

Surround SPKR = LARGE

Surround Back SPKR = LARGE

Sub woofer = YES

y ZONE

button

Press this button to activate the Zone system.
“MULTI” indicator will be illuminated in the display.
(See page 66)

u ZONE SPEAKER button

Press this button to activate the Zone Speaker
system. “MULTI” indicator will be illuminated in the
display. (See page 66)

q POWER switch and STANDBY

indicator

When this switch is pressed once, the unit turns ON
and the display illuminates. When pressed again, the
unit turns OFF and the STANDBY indicator will be
illuminated.

w INPUT SELECTOR knob

(AUDIO/ VIDEO)

This knob is used to select the input sources. (See
page 39)

e SURROUND MODE button

Press this button to select the surround mode.

r AUTO (Auto surround) button

Press this button to select the AUTO mode from the
surround modes. When this mode is selected, the
unit determines the surround mode corresponding to
a digital input signal automatically.

i MENU

button

Press this button to enter the SETUP MAIN MENU.

o EXIT

button

Press this button to exit from the SETUP MAIN
MENU.

!0 BAND

button

Press this button to switch between FM, AM, XM (XM
Ready) and SIRIUS (SIRIUS Ready) in the TUNER
mode.

!1 T-MODE

button

Press this button to select the auto stereo mode or
mono mode when the FM band is selected.
The “AUTO” indicator lights in the auto stereo mode.
(See page 49)

!2 INFRARED receiving sensor window

This window receives infrared signals for the remote
controller.

!3 MEMORY

button

Press this button to enter the tuner preset memory
numbers or station names. (See page 49)

!4 CLEAR

button

Press this button to cancel the station-memory
setting mode or preset scan tuning. (See page 50)

!5 VOLUME control knob

This knob is used to adjust the overall sound level.
Turning the control clockwise increases the sound
level.

!6 DISPLAY

button

Press this button to change the FL display mode.

!7 M-DAX

button

Press this button to select M-DAX processing for
input source. (See page 40)

!8 TOP button

Press this button to return to the top screen of the
main menu when confi guring setup items.
(See page 21)
Also, press this button to return to the top screen of
the network when using the network.

!9 Cursor (

5, ∞, 2, 3) / ENTER button

Press these buttons to operate the SETUP MAIN
MENU, NETWORK and TUNER function.

@0 7.1CH INPUT button

Press this button to select the output of an external
multichannel player.

@1 MIC

jack

Automatically measure speaker characteristics using
the included microphone. (See page 27)

@2 THX

button

Press this button to select THX processing for input
source.

@3 HEADPHONE jack for stereo headphones

This jack may be used to listen to the unit’s output
through a pair of headphones. Be certain that the
headphones have a standard 1/4” stereo phono
plug.

NAMES AND FUNCTION

TOP

ZONE

SPEAKER

DISPLAY

INPUT

7.1CH

DIRECT

PURE

PHONES

THX

M-DAX

MODE

SURROUND

CLEAR

MEMORY

T-MODE

BAND

EXIT

ZONE

ENTER

DOWN

VOLUME

INPUT

SELECTOR

AUTO

SETUP MIC

HDMI

M-DAX

PURE DIRECT

POWER ON/STANDBY

STANDBY

AV PRE TUNER AV8003

t y u i o !0 !1

!3!4

FRONT PANEL

AV8003_U_01_ENG 1_4.indd 5

08.4.30 10:58:37 AM