Marantz AV8003 User Manual

Page 49

CONNECTIONS

SETUP

BASIC

OPERA

TION

REMOTE

CONTROLLER

TROUBLESHOOTING

OTHERS

NAMES AND

FUNCTION

ADV

ANCED

OPERA

TION

ENGLISH

DOLBY HEADPHONE MODE

This feature simulates the waveforms of the actual
sounds heard from the speakers.
When headphones are used, the MENU button
automatically switches to the Dolby headphone
mode.
The OSD that appears when the MENU button is
pressed is shown below.

H E A D P H O N E

D O L B Y H P M O D E : D H
S U R R O U N D : P L II M V

L L E V E L : + 1 0 . 0 d B
R L E V E L : 0 . 0 d B

DOLBY HP (Headphone) MODE can be selected
with the left and right cursor buttons.
BYPASS

→

DH (DOLBY Headphone)

→

BYPASS

BYPASS: Bypasses the Dolby headphone mode

and delivers ordinary 2-channel stereo.

DH: Dolby Headphone is a signal processing

system that delivers a sound similar to
room speakers.

It makes it possible to experience the
volume and space of a 5-channel
surround system using ordinary stereo
headphones.

When the PURE DIRECT mode is selected, Dolby
surround processing is bypassed and “

✽✽✽

” is

displayed as the mode indication.

The surround mode can be selected when the
modes in DH is selected.

L/R LEVEL can be set in the ±12 dB range.

Notes:

• The surround mode returns to the previous setting as

soon as the plug is removed from the jack.

• In headphone mode, Tone Control and ACOUSTIC

EQ are not available.

ATTENUATION TO ANALOG INPUT SIGNAL

If the selected analog audio input signal is greater
than the capable level of internal processing, the
“PEAK” indicator will light up on the front display.
If this happens, switch the remote controller to
AMP mode and press the < / > button until 004 is
displayed. Then press the ATT button.
“ATT” indicator will be illuminated when this function
is activated. The signal-input level is reduced by
about half. Attenuation will not work with the output
signal of TAPE-OUT, CD/CD-R, VCR1-OUT and
DSS/VCR2-OUT.
This function is memorized for each individual input
source.

7.1 CH INPUT

This unit is equipped for future expansion through the
use of Multi channel Super Audio CD multichannel
player or DVD-Audio player.
When this is selected, the input signals connected to
the L(front left), R (front right), CENTER, SL (surround
left), SR (surround right) and SBL (surround back left)
and SBR (surround back right) channels of the 7.1
CH. In jacks are output directly to the front (left and
right), center, surround (left and right) and surround
back speaker systems as well as the pre-out jacks
without passing through the surround circuitry.
In addition, the signal input to the SW (subwoofer)
jack is output to the PRE OUT SW (subwoofer) jack.
When 7.1 CH. INPUT is selected, the last video input
used remains routed to the Monitor Outputs.
This permits simultaneous viewing with video sources

TOP

ZONE

SPEAKER

DISPLAY

INPUT

7.1CH

DIRECT

PURE

PHONES

THX

M-DAX

MODE

SURROUND

CLEAR

MEMORY

T-MODE

BAND

EXIT

ZONE

DOWN

VOLUME

INPUT

SELECTOR

AUTO

SETUP MIC

HDMI

M-DAX

PURE DIRECT

POWER ON/OFF

STANDBY

AV PRE T

AV PRE TUNER AV8003

ENTER

TOP

ZONE

SPEAKER

DISPLAY

INPUT

7.1CH

DIRECT

PURE

PHONES

THX

M-DAX

MODE

SURROUND

CLEAR

MEMORY

T-MODE

BAND

EXIT

ZONE

DOWN

VOLUME

INPUT

SELECTOR

AUTO

SETUP MIC

HDMI

M-DAX

PURE DIRECT

POWER ON/OFF

STANDBY

AV PRE TUNER AV8003

ENTER

≠

Select a desired Video source to decide the

routed video signal to the Monitor Outputs.

Press

the

7.1 CH INPUT button on the front

panel or switch the remote controller to AMP
mode and press the < / > button until 002 is
displayed. Then press 7.1 CH IN on the remote
controller to switch to 7.1 channel input.

If it is necessary to adjust the output level of

each channel, press the < / > button until 004
is displayed. Press the CH SELECT button on
the remote controller.

Adjust the speaker output levels so that you can

hear the same sound level from each speaker
at the listening position. For the front left, front
right, center, surround left, surround right and
surround back speakers, the output levels can
be adjusted between –12 to +12 dB.

The subwoofer can be adjusted between –18

and +12 dB.

These adjustments result will be stored to 7.1

CH. INPUT memory.

Adjust the main volume with the MAIN VOLUME

knob or the VOL + / – buttons on the remote
controller.

To cancel the 7.1 CH. INPUT, press the 7.1 CH
INPUT button on the front panel or press 7.1 CH IN
on the remote controller.

Notes:

• When the 7.1 CH. Input is in use, you may not select

a surround mode, as the external decoder determines
processing.

• In addition, there is no signal at the record outputs

when the 7.1 CH. Input is in use.

• Furthermore, the following functions are not

available during 7.1 CH Input use.

Test Tone, NIGHT MODE, Source Direct, Pure

Direct, RE-EQ, Tone Control, Multi EQ.

AV8003_U_Eng.indb 46

08.4.28 10:40:23 AM