Marantz AV8003 - Manual (Page 53)

CONNECTIONS
SETUP
BASIC
OPERA
TION
REMOTE
CONTROLLER
TROUBLESHOOTING
OTHERS
NAMES AND
FUNCTION
ADV
ANCED
OPERA
TION
50
ENGLISH
MANUAL PRESET MEMORY
3. 3.
4. 4.
5.
TOP TOP
ZONE ZONE SPEAKER SPEAKER
DISPLAY DISPLAY INPUT INPUT 7.1CH 7.1CH DIRECT PURE
PHONES
THX THX M-DAX M-DAX
MODE SURROUND CLEAR MEMORY MEMORY T-MODE T-MODE BAND BAND EXIT EXIT MENU MENU ZONE ZONE
DOWN
VOLUME
UP
INPUT SELECTOR
AUTO
SETUP MIC SETUP MIC
HDMI HDMI
M-DAX
PURE DIRECT
POWER ON/OFF STANDBY
AV PRE TUNER AV8003 AV PRE TUNER AV8003
ENTER ENTER
3. 2. 4.
(Using the unit)
1. Tune into the radio station you desire (Refer to
the “MANUAL TUNING” or “AUTO TUNING”
section).
2. Press the MEMORY button on the front panel.
“– –“ (preset number) starts blinking on the
display.
3. Select the preset number by pressing the 1
or 2 cursor buttons, while this is still blinking
(approx. 5 seconds)
4. Press the MEMORY button again to enter. The
display stops blinking.
The station is now stored in the specifi ed preset
memory location.
(Using the remote controller)
1. Tune into the radio station you desire (Refer to
the “MANUAL TUNING” or “AUTO TUNING”
section).
2. Switch the remote controller to TUNER mode.
3. Press the < / > button until 002 is displayed in
TUNER mode.
4. Press the MEMORY button on the remote
controller. “– –“ (preset number) starts blinking
on the display.
5. Enter the desired preset number by pressing
the numeric buttons.
Note:
• When entering a single digit number (2 for example),
either input “02” or just input “2” and wait for a few
seconds.
4. Up to 10 channels can be displayed at a time.
If there are more than 10 channels, press
P-INFO button on the remote controller once
more to display the next page.
The list display will disappear automatically in 5
seconds.
CLEARING STORED PRESET STATIONS
You can remove preset stations from the memory
using the following procedure.
TOP TOP
ZONE ZONE SPEAKER SPEAKER
DISPLAY DISPLAY INPUT INPUT 7.1CH 7.1CH DIRECT DIRECT PURE PURE
PHONES PHONES
THX THX M-DAX M-DAX
MODE MODE SURROUND SURROUND CLEAR CLEAR MEMORY MEMORY T-MODE T-MODE BAND BAND EXIT EXIT MENU MENU ZONE ZONE
DOWN DOWN
VOLUME VOLUME
UP UP
INPUT INPUT SELECTOR SELECTOR
AUTO AUTO
SETUP MIC SETUP MIC
HDMI HDMI
M-DAX M-DAX
PURE DIRECT PURE DIRECT
POWER ON/OFF POWER ON/OFF
STANDBY STANDBY
AV PRE TUNER AV8003 AV PRE TUNER AV8003
ENTER ENTER
3. 2.
2. 2.
3.
1. Recall the preset number to be cleared with
the method described in “Recalling” a preset
station.
2. Press the MEMORY button on the front panel
or press the MEMORY button on the remote.
3. The stored preset number blinks in the display
for 5 seconds. While blinking, press the
CLEAR button on the front panel or the remote
controller.
4. “xx CLEAR” appears on the display to indicate
that the specified preset number has been
cleared.
Note:
• To clear all stored preset stations, press and hold the
CLEAR and the ENTER buttons for two seconds.
3. Preset stations are recalled in sequence (No.1
→ No.2 → etc.) for 10 seconds each.
No stored preset number will be skipped.
4. You can fast forward the preset stations, press
the 2 cursor button continuously.
5. When the desired preset station is received,
cancel the preset scan operation by pressing
the CLEAR button or P-SCAN button on the
remote controller.
PRESET CHANNEL LIST DISPLAY
A complete list of the broadcast channels stored in
this unit can be displayed.
2. 2.
2. 4. 2. 4.
1. Switch the remote controller to TUNER mode.
2. Press < / > on the remote controller to display
002, then press P-INFO button.
3. The list of preset channels will be displayed on
the screen of the TV monitor connected to this
unit.
P R E S E T L I S T
N O . 1 F M 8 7 . 1 0 M H z
N O . 2 F M 9 3 . 1 0 M H z
N O . 3 F M 9 4 . 7 0 M H z
N O . 1 0 F M 1 0 5 . 7 0 M H z
R E T U R N N E X T E X I T
On the unit, multicast channels are also
displayed, as shown below, when an HD Radio
channel is set to the preset channels.
P R E S E T L I S T
N O . 1 F M 8 7 . 1 0 M H z
N O . 2 F M 9 3 . 1 0 M H z
N O . 3 F M 9 4 . 7 0 M H z
N O . 4 F M 9 4 . 7 0 M H z - 3
N O . 5 F M 9 4 . 7 0 M H z - 4
N O . 1 0 F M 1 0 5 . 7 0 M H z
In the list of preset channels above, preset
numbers 4 and 5 are the multicast channels for
preset number 3.
RECALLING A PRESET STATION
2. 2.
(Using the unit)
1. Select the desired preset station by pressing
the 1 or 2 cursor buttons on the front panel.
(Using the remote controller)
1. Switch the remote controller to TUNER mode.
2. Press the 1 or 2 cursor buttons to tune in the
deseired preset station.
Or enter the preset station number with the
numeric buttons.
Note:
The same operations performed using the 1 or 2
buttons can be performed using the CH +/- buttons
when the remote controller is in TUNER mode.
PRESET SCAN
4.
2. 2.
2.5. 2.5.
5.
(Using the remote controller)
1. Switch the remote controller to TUNER mode.
2. Press the < / > button until 002 is displayed and
press the P-SCAN button on the remote.
“PRESET SCAN” appears on the front display
and then the preset station with the lowest
preset number is recalled fi rst.
AV8003_U_Eng.indb 50 AV8003_U_Eng.indb 50 08.4.28 10:40:26 AM 08.4.28 10:40:26 AM