Marantz AV8003 User Manual

Page 27

CONNECTIONS

BASIC

OPERA

TION

ADV

ANCED

OPERA

TION

REMOTE

CONTROLLER

TROUBLESHOOTING

OTHERS

NAMES AND

FUNCTION

SETUP

ENGLISH

1-1 FUNC INPUT SETUP
(ASSIGNABLE DIGITAL INPUT)

The 6 digital inputs can be assigned to a desired
source.
HDMI and COMPONENT inputs can be assigned to
the preferred source.
Use this menu to select which digital input jacks are
to be assigned to which input source.

Select

“FUNC INPUT SETUP” from the

1.INPUT SETUP menu with the

cursor

buttons and press the ENTER button.

F U N C I N P U T S E T U P 1
F U N C : M O D E DIG HDMI COMP V/S

T V :

A U T O

1 1 1 1

D V D : A U T O 2

V C R 1 : A U T O 3 3 3 3
D S S : A U T O 4

R E T U R N N E X T

E X I T

Select a setting with the

, and

cursor

buttons, and assign a mode and input jack
(DIG, HDMI, COMP, V/S).

MODE

AUTO:

Select “AUTO”, for automatic detection of the
digital input signal condition.
If there is no digital signal, but there is an analog
signal present, the analog signal will be played.
"AUTO" is the initial setting of all input sources.

HDMI:

Select “HDMI”, when only a HDMI signal will be
used.

DIG:

Select “DIG”, when only a digital signal will be
used.

ANA:

Select “ANA” for input sources for which no digital
input jacks are used.

DIG

The 6 digital inputs can be assigned to a desired
source.
Assign the number of a digital input jack to the
device.

HDMI

Assign the number of an HDMI input jack to the
device.

Note:

• When FUNCTION MODE is set to HDMI and

HDMI AUDIO of “5. PREFERENCE” is set to
THROUGH, audio is not output from the unit. (See
page 35)

COMP

Assign the number of a component video input
jack to the device.

V/S

Assign the number of a composite video and S-
video input jack to the device.

Note:

• Video and S-video can use the same numbers when

assigning to input functions.

Press

the

ENTER button.

Select each mode setting and input terminal

with the

cursor buttons.

Press

the

ENTER button.

Repeat steps 2-5 until all items are set.

After you complete this portion of the setup,

move the cursor to “NEXT” with the

, and

cursor buttons and then press the

ENTER button to go to the next page.

F U N C I N P U T S E T U P 2
F U N C : M O D E DIG HDMI C0MP V/S

T A P E : A U T O - -

- 1

C D / R : A U T O

5 - -

A U X : A U T O

- - -

S I R I U S
: A U T O

R E T U R N B A C K

E X I T

Repeat steps 2-5 until all items are set.

After you complete this portion of the setup,

move the cursor to “RETURN” with

, and

cursor buttons and press the ENTER button.

To return to the Func Input Setup 1 menu from

the Func Input Setup 2 menu, move the cursor
to “BACK” with the

, and

cursor

buttons and press the ENTER button.

Move the cursor to “RETURN” with the

, and

cursor buttons, and press the ENTER

button to go to the 1.INPUT SETUP menu.

Note:

• Assignments cannot be made in sections with a

✽

mark.

1-2 7.1 CH INPUT SETUP

This menu is for adjusting the speaker levels for 7.1-
channel input sources.
Here you will adjust the volume for each channel so
that they are all heard by the listener at the same
level.

Select

“7.1 CH INPUT SETUP” from the

1.INPUT SETUP menu with the

cursor

buttons and press the ENTER button.

7 . 1 C H I N P U T S E T U P
V I D E O - I N :

L A S T

F R O N T L : 0 d B
C E N T E R : 0 d B
F R O N T R : 0 d B
S U R R . R : 0 d B
S U R R . B R : 0 d B
S U R R . B L : 0 d B
S U R R . L : 0 d B
S U B W : 0 d B

R E T U R N

N E X T

E X I T

Select

“VIDEO-IN” with the

cursor

buttons.

Using

the

cursor buttons, select the

video input source to be played through the
MONITOR OUT jack.

The input source is switched by pressing the

cursor buttons as follows;

LAST

↔

DVD

↔

VCR1

↔

DSS

↔

NET

↔

TAPE

↔

CD/R

↔

AUX

↔

V-OFF

↔

LAST

↔

...

Notes:

• When “LAST” is selected, the source is set to the

source selected before the 7.1 ch input menu was
activated.

• When “V-OFF” is selected, no signal is emitted from

MONITOR OUT jack.

Select desired channel with the

cursor

buttons.

Using

the

cursor buttons, adjust the

volume level of each channel.

Move the cursor to “RETURN” with the

, and

cursor buttons, and press the ENTER button to go

to the 1.INPUT SETUP menu.

Note:

• The volume level can be set between -12 dB and

+12 dB in 1 dB increments on all channels except the
subwoofer (SUB W), which can be set from -18dB
to +12 dB in 1 dB increments.

AV8003_U_Eng.indb 24

08.4.28 10:40:10 AM