Marantz AV8003 User Manual

Page 50

CONNECTIONS

SETUP

BASIC

OPERA

TION

REMOTE

CONTROLLER

TROUBLESHOOTING

OTHERS

NAMES AND

FUNCTION

ADV

ANCED

OPERA

TION

ENGLISH

AUX INPUT

If you don’t need to connect 7.1 Ch. input terminals
with multi channel decoder,
L(front left) and R (front right) inputs terminals are
available as AUX input.
In this case, You can connect additional audio source
to AUX as other audio input terminals.

TOP

ZONE

SPEAKER

DISPLAY

INPUT

7.1CH

DIRECT

PURE

PHONES

THX

M-DAX

MODE

SURROUND

CLEAR

MEMORY

T-MODE

BAND

EXIT

ZONE

DOWN

VOLUME

INPUT

SELECTOR

AUTO

SETUP MIC

HDMI

M-DAX

PURE DIRECT

POWER ON/OFF

STANDBY

AV PRE TUNER AV8003

ENTER

To select AUX, turn the INPUT SELECTOR knob on
the front panel, or press HOME button and press 6
button on remote controller.

VIDEO ON/OFF

When no video signal is connected to the unit or
a DVD, etc., is connected directly to your TV, the
unnecessary video circuit can be turned off by
selecting the “VIDEO OFF” setting.
To select video off, switch the remote controller to
AMP mode and press the < / > button until 004 is
displayed. Then press the VIDEO OFF button.

TOP

ZONE

SPEAKER

DISPLAY

INPUT

7.1CH

DIRECT

PURE

PHONES

THX

M-DAX

MODE

SURROUND

CLEAR

MEMORY

T-MODE

BAND

EXIT

ZONE

DOWN

VOLUME

INPUT

SELECTOR

AUTO

SETUP MIC

HDMI

M-DAX

PURE DIRECT

POWER ON/OFF

STANDBY

AV PRE TUNER AV8003

ENTER

V-OFF

The “V-OFF” indicator on the main unit display panel
will light.

TV AUTO ON/OFF FUNCTION

This function allows the component connected to the
TV-VIDEO in jack to control the power (ON/OFF) to
the unit.

AUTO POWER ON

Be sure the TV auto mode is ENABLED. (Refer

to page 34)

Connect your TV TUNER (etc) to the TV-

VIDEO in terminal. Be sure to connect the
VIDEO input.

Turn OFF the power to the TV TUNER and the

unit.

Turn ON the TV TUNER and tune in a receivable

station.

When the station is received, this unit turns ON

and TV is selected automatically.

AUTO POWER OFF

In the above situation, turn the TV TUNER OFF

or select a channel that does not contain any
broadcast.

The power to the unit switches to STANDBY

after approx. 5 minutes.

Notes:

• AUTO POWER OFF is canceled if this unit is set to

a source other than TV.

The function reactivates when TV is selected again.

• Some TV broadcasts may cause the TV AUTO

FUNCTION to turn ON.

• The S-Video terminal does not support “TV AUTO

ON/OFF” function.

• This function is inactive when STANDBY MODE

is set to ECONOMY. To use this function, set
STANDBY MODE to NORMAL.

LIP.SYNC

Depending on the image device (TV, monitor,
projector, etc.) connected to the unit a time lag can
occur between image signal processing and audio
signal processing. Though minor, this time lag can
interfere with movie and music enjoyment. The LIP.
SYNC feature delays the audio signal with respect
to the image signal output from the unit to correct
the time lag between the sound and image. It can be
operated with the “LIP.SYNC” and

and

cursor

buttons of the remote controller. To select Lip-sync
mode, set the remote controller to the AMP mode,
press the < / > button until 002 is displayed. Press
the LIP. SYNC button. The initial setting is OFF (0
ms).The time lag can be adjusted in 10 ms steps up
to 200 ms.
Watch the picture on the image device (i.e., TV,
monitor, projector, etc.) as you adjust the time lag.

Note:

• The LIP.SYSNC feature turns OFF (0 ms) in

the SOURCE/PURE DIRECT mode. When the
SOURCE/PURE DIRECT mode is deactivated, the
set value of the LIP.SYSNC feature is automatically
restored.

• Even if you do not correct the time lag manually this

way, audio and video are automatically synchronized
when the unit is connected to TV or Projector
supporting Auto Lipsync Correction in HDMI 1.3a.
For instructions on Auto Lipsync Correction, see
page 35.

DUAL BACKUP MEMORY

The unit stores settings information in nonvolatile
memory even when the main power supply is turned
off. Using the Dual Backup Memory function, you
can write settings information to another memory
area to back up saved settings for recovery anytime
as needed.

BACKUP

Set up the unit in the state for which you want to
store the settings. Hold the MEMORY and ENTER
buttons on the front panel simultaneously for at least
3 seconds.

TOP

ZONE

SPEAKER

DISPLAY

INPUT

7.1CH

DIRECT

PURE

PHONES

THX

M-DAX

MODE

SURROUND

CLEAR

MEMORY

T-MODE

BAND

EXIT

ZONE

DOWN

VOLUME

INPUT

SELECTOR

AUTO

SETUP MIC

HDMI

M-DAX

PURE DIRECT

POWER ON/OFF

STANDBY

AV PRE TUNER AV8003

ENTER

“MEMORY SAVING” is displayed and the unit’s
settings are saved. The stored settings information
is retained until Dual Backup Memory is used again
and the information is overwritten.

M E M O R Y S A V I N G

Note:

• The following settings values cannot be backed

up.

• Main Zone Volume
•

Zone

Volume

• Zone Speaker Volume

AV8003_U_Eng.indb 47

08.4.28 10:40:24 AM