Marantz AV8003 - Manual (Page 10)

CONNECTIONS
NAMES AND
FUNCTION
SETUP
BASIC
OPERA
TION
ADV
ANCED
OPERA
TION
REMOTE
CONTROLLER
TROUBLESHOOTING
OTHERS
ENGLISH
7
y BALANCED PREOUT
(L, R,SL, SR, SBL, SBR, C)
Connect the L (front left), R (front right), C (center), SL
(Surround left), SR (Surround right), SBL (Surround
back left), and SBR (Surround back right) terminals
to the balanced input terminals of a power amp such
as the MM8003.
u NETWORK
Connect to a network device such as a router or
hub.
This allows you to play back music, photos, and
movie fi les stored on a connected network device.
i Subwoofer Output
These are subwoofer outputs and each one includes
both unbalanced and balanced jack confi gulations.
Connect this jack to the line level input of a powered
subwoofer.
o SPEAKER C switch
Set to ON to connect a bi-amp to this unit or set to
OFF for normal connection (surround back and zone
speakers). (See page 19)
!0 SIRIUS terminal
Connect the SiriusConnect Home tuner.
See page 17 for connecting information.
!1 XM terminal
Connect the XM Mini Tuner and Home Dock.
See page 17 for connecting information.
!2 RS-232C
The RS-232C port is to be used in connection with an
external controller to control the operation of the unit
by using an external device.
The RS-232C port may also be used in the future to
update the operating software of the unit so that it will
be able to support new digital audio formats and the
like as they are introduced.
!3 AC INLET
Plug the supplied power cable into this AC INLET
and then into the power outlet on the wall.
This unit can be powered by 120V AC only.
!4 CD/CDR Input Selection Switch
Switches between BALANCED and UNBALANCED
for the CD/CDR IN terminals.
Notes:
• Always set the input selection before turning on the
power. Equipment failure may result If the input
selection is switched while the power is on.
• Audio may not be output from the main unit if the
input to the unit differs from the setting of the Input
Selection Switch.
!5 BALANCED CD/CDR IN
Connect to the balanced output terminal of a Super
Audio CD Player or similar player.
The UNBALANCED CD/CDR input terminals are
the CD/CDR IN terminals in
@3 .
Note:
D o n o t c o n n e c t t o t h e B A L A N C E D a n d
UNBALANCED terminals at the same time.
!6 7.1 CHANNEL or AUX INPUT
By connecting a DVD Audio player, Super Audio CD
multichannel player, or other components that has a
multichannel port, you can playback the audio with
5.1 channel or 7.1 channel outputs.
!7 EMITTER OUT
The signals input to the IR RECEIVER IN terminals
are output to this terminal. External devices can be
controlled by connecting them to this terminal.
!8 IR RECEIVER IN
Connect to an external IR receiver.
!9 FLASHER IN (Flasher input terminal)
These terminals are to control the unit from each zone.
Connect the control signal from a Keypad, etc.
@0 DC TRIGGER output terminal
Connect a device that needs to be triggered by DC
under certain conditions (screen, power strip, etc…)
Use the system OSD setup menu to determine the
conditions by which these jack will be active.
(See page 36)
Note:
• This output voltage is for (status) control only, It is
not suffi cient for drive capability.
REAR PANEL
e Zone Outputs
(Audio output A/B, Video)
These are the audio and video output jacks for the
Multi zone.
Connect these jacks to optional audio power
amplifi ers or video display devices to listen and view
the source selected by the zone system in a remote
room.
r MONITOR OUT
These are monitor outputs and each one includes
both composite video and S-video confi gurations.
When connecting two video monitors or televisions,
be aware that the OSD interface can be used with
both MONITOR OUT connections.
t UNBALANCED PREOUT
(L, R, SL, SR, SBL, SBR, C)
Connect the L (front left), R (front right), C (center), SL
(Surround left), SR (Surround right), SBL (Surround
back left), and SBR (Surround back right) terminals
to the unbalanced input terminals of a power amp
such as the MM8003.
q FM antenna terminal (75 ohms)
Connect an external FM antenna with a coaxial
cable, or a cable network FM source.
AM antenna and ground terminals
Connect the supplied AM loop antenna. Use the
terminals marked “AM” and “GND”. The supplied AM
loop antenna will provide good AM reception in most
areas. Position the loop antenna until you hear the
best reception.
w COMPONENT VIDEO INPUT/
OUTPUT
If your DVD player or other device has component
video connectors, be sure to connect them to these
component video connectors on the unit. This unit
has 4 component video input connectors to obtain
the color information (Y, C
B , C R ) directly from the
recorded DVD signal or other video component and
two component video outputs connector to output it
directly into the matrix decoder of the display device.
By sending the pure DVD component video signal
directly, the DVD signal forgoes the extra processing
that normally would degrade the image. The result is
vastly increased image quality, with incredibly life like
colors and crisp detail.
The Monitor Out 2 terminal is also used for ZONE
output.
L L SR SR SL SL R R
R R
SR SR SL SL
SW SW C C
SBR SBR SBL SBL
L L
SBL SBL SW SW C C SBR SBR
FM FM ( (75 75 Ω Ω)) GND GND AM AM
ANTENNA ANTENNA
OUT OUT
PUT PUT 1 1
OUT OUT
PUT PUT 2 2
INPUT 3 INPUT 3((VCR1 VCR1)) OUTPUT 1 OUTPUT 1 OUTPUT 2 OUTPUT 2 INPUT 1 INPUT 1( (TV TV) ) INPUT 4 INPUT 4((DSS/VCR2 DSS/VCR2)) INPUT 2 INPUT 2( (DVD DVD) )
COMPONENT COMPONENT VIDEO VIDEO
C CB B // P PB B C CR R // P PR R C CR R // P PR R C CR R // P PR R C CB B // P PB B C CB B // P PB B Y Y Y Y Y Y
INPUT 1 INPUT 1( (TV TV) )
INPUT 4 INPUT 4( (DSS DSS // VCR2 VCR2) ) INPUT 3 INPUT 3( (VCR1 VCR1) )
INPUT 2 INPUT 2((DVD DVD))
RS-232C RS-232C SPEAKER C SPEAKER C SIRIUS SIRIUS
NETWORK NETWORK
ON ON OFF OFF
1 3
CONNECTION GND
HOT(+)
COLD(-)
3 2 1 2
AC IN AC IN
OUT OUT IN IN IN IN OUT OUT VIDEO VIDEO
MONITOR MONITOR OUT OUT DVD DVD( (2 2) ) DSS/VCR2 DSS/VCR2( (4 4) ) TV TV( (1 1) ) ZONE ZONE OUT OUT VCR1 VCR1( (3 3) ) DVD DVD((2 2)) TV TV( (1 1) )
2 2
1 1
FLASHER FLASHER IN IN
IR IR RECEIVER RECEIVER IN IN
6 6 COAX. COAX. 5 5 4 4
OUT OUT
IN IN 1 1
2 2
EMITTER EMITTER OUT OUT SELECTOR SELECTOR
DC OUT DC OUT
R R L L
OUT OUT
R R
OUT OUT
L L TAPE TAPE
OUT OUT IN IN R R OUT OUT
L L
DSS/VCR2 DSS/VCR2
AUDIO AUDIO
BALANCED BALANCED
PRE OUT PRE OUT
UNBALANCED UNBALANCED
TV TV
IN IN SR SR
VCR1 VCR1
IN IN
DVD DVD SL SL
SBR SBR
SBL SBL
SW SW
C C
A A B B
7.1CH 7.1CH IN IN
( (AUX AUX) )
3 3 2 2 1 1 OPT. OPT.
MODEL NO. AV8003 MODEL NO. AV8003
DIGITAL IN DIGITAL IN DIGITAL OUT DIGITAL OUT MAIN MAIN ZONE ZONE CD/CDR CD/CDR
IN IN
REMOTE REMOTE 1 2 3
BALANCED BALANCED UNBALANCED UNBALANCED
IN IN OUT OUT
S-VIDEO S-VIDEO
IN IN OUT OUT DSS/VCR2 DSS/VCR2( (4 4) ) VCR1 VCR1( (3 3) ) MONI. OUT MONI. OUT
CD/CDR BALANCED IN CD/CDR BALANCED IN
ZONE OUT ZONE OUT
CONNECTION GND
HOT(+)
COLD(-)
3 2 1
3 1 2 3 1 2 3 1 2 3 1 2
3 1 2 3 1 2 3 1 2 3 1 2
3 1 2 3 1 2
PUSH PUSH
q w t y
u !3 i !6 @1 @2
e @0
o !0 !2!1 !5 !4 !7 !8 !9
@3
@6
@4
@5
r e
AV8003_U_Eng.indb 7 AV8003_U_Eng.indb 7 08.4.28 10:40:05 AM 08.4.28 10:40:05 AM