Marantz AV8003 - Manual (Page 66)

CONNECTIONS
SETUP
BASIC
OPERA
TION
REMOTE
CONTROLLER
TROUBLESHOOTING
OTHERS
NAMES AND
FUNCTION
ADV
ANCED
OPERA
TION
63
ENGLISH
PRESET MEMORY
You can store the desired channel in the Preset
Memory.
(You can preset 50 SIRIUS Radio stations in addition
to FM/AM stations.)
TOP TOP
ZONE ZONE SPEAKER SPEAKER
DISPLAY DISPLAY INPUT INPUT 7.1CH 7.1CH DIRECT PURE
PHONES
THX THX M-DAX M-DAX
MODE SURROUND CLEAR CLEAR MEMORY MEMORY T-MODE T-MODE BAND BAND EXIT EXIT MENU MENU ZONE ZONE
DOWN DOWN
VOLUME VOLUME
UP UP
INPUT SELECTOR
AUTO
SETUP MIC SETUP MIC
HDMI HDMI
M-DAX
PURE DIRECT
POWER ON/OFF
STANDBY
AV PRE TUNER AV8003 AV PRE TUNER AV8003
ENTER ENTER
3. 2. 4.
3. 3.
2. 2.
4.
(Using the unit)
1. Tune into the desired channel.
2. Press the MEMORY button on the front panel.
”- -” (preset number) starts blinking on the
dispIay.
- - S R 0 4 0
3. Select the preset number by pressing the 1
or 2 cursor buttons, While this is still blinking
(approx. 5 seconds)
0 1 S R 0 4 0
4. Press the MEMORY button again to enter.
The display stops blinking.
The station is now stored in the specifi ed preset
memory location.
(Using the remote controller)
1. Tune into the desired channel.
2. Press the < / > button until 002 is displayed.
3. Press the MEMORY button on the remote
controller. “- -” (preset number) starts blinking
on the display.
4. Enter the desired preset number by pressing
the numeric buttons.
Note:
• When entering a single digit number (2 for example),
either input “02” or just input “2” and wait for a few
seconds.
CHECKING THE SIRIUS PRESET CHANNEL
The preset channel can be checked on the on screen
display.
3.
4. 3.
4.
2. 2.
(Using the remote controller)
1. Switch the remote controller to TUNER mode.
2. Press the < / > button until 002 is display.
3. Press the P-INFO button. to view a list of tuner
preset channeI on the on screen display.
4. If there are 10 or more preset channel, Press
the P-lNFO button. again.
S I R I U S P R E S E T L I S T
N O . 1 S R 0 1 0 X X X X X X X X X X
N O . 2 S R 0 1 1 X X X X X X X X X X
N O . 3 S R 0 1 5 X X X X X X X X X X
N O . 4 S R 0 2 2 X X X X X X X X X X
N O . 5 S R 1 2 5 X X X X X X X X X X
Note:
• The preset channel indication disappears in about 5
sec.
PRESET SCAN
3.
5. 3.
5.
2. 2.
5. 5.
1. Switch the remote controller to TUNER mode.
2. Press the < / > button until 002 is displayed.
3. press the P-SCAN button on the remote
controller. “PRESET SCAN” appears on the
display and then the preset station with the
lowest preset number is recalled fi rst.
4. Preset stations are recalled in sequence (No.1
→ No.2 → etc.) for about 5-10 seconds each.
The time changes by the received condition. No
stored preset number will be skipped.
5. Pressing the 2 cursor button during prescanning
speeds up scanning.
Also, pressing the 1 cursor button returns to
the previous preset station.
When the desired preset station is received,
cancel the preset scan operation by press the
P-SCAN button.
AV8003_U_Eng.indb 63 AV8003_U_Eng.indb 63 08.4.28 10:40:34 AM 08.4.28 10:40:34 AM