Roland SH-4d Digital Desktop Synthesizer - Manual (Page 174)

PATTERN REVERB
174
Parameter Value Explanation
LF Damp G -36–0 [dB] Adjusts the LF damp attenuation amount (0: no effect).
HF DampF
4000–12500 [Hz] (*6) Adjusts the frequency above which the high-frequency portion of the reverb sound is
cut.
HF Damp
G
-36–0 [dB] Adjusts the HF damp attenuation amount (0: no effect).
GS Reverb
Parameter Value Explanation
Char
ROOM1,
ROOM2,
ROOM3,
HALL1,
HALL2,
PLATE,
DELAY,
PAN-DELAY
This selects the reverb type.
Pre LPF 0–7 Adjusts the amount of high-frequency attenuation for the sound fed into the reverb.
Time 0–127 Adjusts the decay length of the reverb sound.
Feedback 0–127 Adjusts the level at which the reverb sound is returned to the input.
SRV-2000
Parameter Value Explanation
Selection
R0.3, R1.0, R7.0, R15, R22, R26, R32, R37, H15, H22,
H26, H32, H37, P-B, P-A
Selects the type of reverb offered by the Roland SRV-2000
digital reverb.
PreDelay
0–160 Adjusts the delay time from when the direct sound plays until
the reverb sound is heard.
Time 0.1–99.0 [sec] Adjusts the decay length of the reverb sound.
HF Damp 0.05–1.00 Adjusts the high-frequency portion of the reverb.
Density 0–9 Adjusts the density of the late reverberation.
Attack
Gain 0–9 Adjusts the gain of the early reflections.
Attack
Time 0–9 Adjusts the time of the early reflections.
ER Density 0–9 Adjusts the density of the early reflections.
ER Level 0–99 Adjusts the volume of the early reflections.
Low Freq 0.04–1.00 [kHz] Sets the center frequency of the low range.
Low Gain -24–+12 [dB] Adjusts the boost/cut of the low frequency range.
Mid Freq 0.25–9.99 [kHz] Sets the center frequency of the mid range.
Mid Gain -24–+12 [dB] Adjusts the amount of boost/cut of the mid-frequency range.
Mid Q
0.2–9.0 Sets the bandwidth of the mid-frequency range.
Higher values make the bandwidth narrower.
HighFreq 0.80–9.99 [kHz] Sets the center frequency of the high range.
HighGain -24–+12 [dB] Adjusts the boost/cut of the high frequency range.
High Q
0.2–9.0 Sets the bandwidth of the high frequency range.
Higher values make the bandwidth narrower.
SRV-2000NL （ NON-LINEAR ）
Parameter Value Explanation
PreDelay 0–120 Adjusts the delay time from when the direct sound plays until the reverb sound is heard.
ReverbTime 0.9–+99.0 [sec] Adjusts the decay length of the reverb sound.
GateTime 10–450 Adjusts the time it takes to cut off the reverb once the reverb begins to sound.
Low Freq 0.04–1.00 [kHz] Sets the center frequency of the low range.
Low Gain -24–+12 [dB] Adjusts the boost/cut of the low frequency range.
Mid Freq 0.25–9.99 [kHz] Sets the center frequency of the mid range.
Mid Gain -24–+12 [dB] Adjusts the amount of boost/cut of the mid-frequency range.
Mid Q
0.2–9.0 Sets the bandwidth of the mid-frequency range.
Higher values make the bandwidth narrower.
HighFreq 0.80–9.99 [kHz] Sets the center frequency of the high range.
HighGain -24–+12 [dB] Adjusts the boost/cut of the high frequency range.