Yaskawa P7B Drive Bypass - Manual (Page 284)

Index - 4
Setting Method Selection (MOP).................. 5-36, A-24
Source (b1-01)............... 2-12, 2-13, 2-16, 3-3, 3-5, A-4
Frequency References 1 thru 4 – See Preset Speeds
Full Load Amps (FLA) ........................ 4-7, 5-26, 6-12, A-11
Fuse Blown Protection .....................................................C-4
FWD Indicator.................................................................. 3-4
G
Gain Adjustments ....................................... 5-26, 5-27, A-16
Gate Drive PCBs
Inspecting ..................................................................7-2
Spare Parts......................................................... F-2, F-3
Ground Fault (GF)...................................................5-31, 6-5
Ground Fault Interrupter (GFI) ....................................... E-4
Troubleshooting ...................................................... 6-18
Grounding ...................................................................... 2-11
Protection ..................................................................C-4
Shield Wire.............................................................. 2-13
H
HAND
Frequency Reference Selection.........................3-4, A-4
Indicators........................................................... 3-4, 3-5
Key ............................................................................ 3-4
Function Selection .......................................... A-25
Mode ......................................................................... 3-4
Troubleshooting ...................................................... 6-15
Hardware Protection Parameters ....................................A-22
Harmonics, Power Supply ...................................... C-2, C-3
Heatsink – See Cooling Fins
Heatsink Fan – See Fan, Heatsink Cooling
High-Slip Braking ..........................................................A-23
H/O/A (Hand/Off/Auto) – See Digital Operator
Horsepower, converting to kW........................................5-39
Humidity..........................................................................1-11
Ambient Operating....................................................C-4
Hunting Prevention
Parameters ...............................................................A-23
Troubleshooting ...................................................... 6-18
I
IEC IP00 – See Open Chassis
IEC IP20 – See Enclosed wall-mounted type
IGBT (Transistor Module)
Inspecting ...................................................................7-2
Resistance Test ............................................6-20 to 6-22
Spare Parts..........................................................F-2, F-3
INCREASE Key ...............................................................3-3
Troubleshooting ....................................................... 6-14
Indicators, Mode .....................................................3-4 to 3-6
Initial Start-up ......................................................4-1 to 4-10
Initialization
Mode Selection ................................................. 5-2, 5-36
Parameters ................................................................ A-2
Specification Selection ................................... 5-2, A-25
Input
Diodes, Inspecting ..................................................... 7-2
Fuses .......................................................... 2-9, E-2, E-3
Multi-function Terminals – See Analog Inputs and
Digital Inputs
Phase Loss Detection Level............................. 6-6, A-22
Terminal Status (U1-10) ........................................ A-26
Voltage ................................................... A-10, C-2, C-3
Setting..............................................4-5, 5-15, A-10
Inputs
Analog – See Analog Inputs
Digital – See Digital Inputs
Frequency Reference – See Frequency Reference
Inspection
Periodic ...................................................................... 7-2
Receiving ................................................................... 1-3
Installation
Electrical ................................................................... 2-1
Physical ..................................................................... 1-1
Adverse Conditions ............................................ 7-3
Orientation & Clearances ................................. 1-12
Site............................................................ 1-11, C-4
Integral Limit (PI) ........................................................... 5-13
Interference ........................................................ 2-19 to 2-21
IPM (Intelligent Power Module)
Inspecting................................................................... 7-2
Spare Parts ......................................................... F-2, F-3
J
Jog Frequency Reference ..............................2-13, 2-16, A-8
Jump Frequency ...............................................................A-9
Troubleshooting ....................................................... 6-19
K
Keypad — See Digital Operator
kVA
Auto-Tuning ............................................................ 5-39
Error................................................................ 6-11, 6-13
Parameters Affected by .............................................B-2
Selection ................................................................. A-23