Yaskawa P7B Drive Bypass - Manual (Page 16)

Physical Installation 1 - 4
Enclosure Data
Table 1.2 208V Enclosure Data
Input
Volts
HP 1
Drive
Model
CIMR-
Bypass 2
Model
Number
NEC
FLA
OL
110%
1 min
Heat 3
Loss
Watts
Enclosure Dimensions 4
NEMA 1 & NEMA 12 -FVFF
H W D
inches
Weight 5
of
Assembly
Enclosure Dimensions w/Add-on 4
NEMA 1 & NEMA 12-FVFF
H W D
inches
Weight 5 of
Assembly
+Add-on
Box
Electrical
Schematic
208
0.5 P7U22P21A P7B_D002 2.4 2.6 68
29.48 19.06 13.66
Dimension Drawing 6
S-5542
115 lbs
43.35 19.06 13.66
Dimension Drawing
S-5543
156 lbs
P7B-00
0.75 P7U22P21A P7B_D003 3.5 3.8 68
1 P7U22P21A P7B_D004 4.6 5.1 78
2 P7U22P21A P7B_D007 7.5 8.2 110
3 P7U22P21A P7B_D010 10.6 11.7 141
5 P7U23P71A P7B_D016 16.7 18.4 202
7.5 P7U27P51A P7B_D024 24.2 26.6 273
10 P7U27P51A P7B_D030 30.8 33.9 365
127 lbs 164 lbs
15 P7U20111A P7B_D046 46.2 50.8 578
20 P7U20151A P7B_D059 59.4 65.3 653
40.48 25.63 14.66
Dimension Drawing 7
S-5544
208 lbs
55.35 25.63 14.66
Dimension Drawing
S-5545
291 lbs
25 P7U20181A P7B_D074 74.8 82.3 746
30 P7U20221A P7B_D088 88.0 96.8 939
221 lbs 307 lbs
40 P7U20301A P7B_D114 114.0 125.4 1340
50 P7U20370A P7B_D143 143.0 157.3 1523
84.00 25.63 26.25 8
Dimension Drawing 9
S-5550
847 lbs
NOT REQUIRED
60 P7U20450A P7B_D169 169.0 185.9 1762
943 lbs
75 P7U20550A P7B_D211 211.0 232.1 2244
100 P7U20750A P7B_D273 273.0 300.3 3003 1214 lbs
125 P7U20900A P7B_D343 343.0 377.3 3296 1330 lbs
150 P7U21100A P7B_D396 396.0 435.6 4029 1423 lbs
Note 1: Horsepower rating is based on a standard NEMA B 4-pole motor.
Note 2: The underscore position in these model numbers codes for the enclosure type: V = NEMA1, B = NEMA12 FVFF.
Note 3: Heat loss is the amount of heat dissipated by the drive at full load with all standard options available inside the enclosure. Drive heat sink losses are
included in the heat loss data. Heat loss data is for the enclosure without the add-on enclosure.
Note 4: Height dimension (H) excludes the mounting screw tabs. Depth dimension (D) excludes MCP disconnect handle.
Note 5: This data represents the total weight with all possible standard options. Weight could be less depending on the options specified.
Note 6: All standard options are available in this size enclosure except options E (RFI Filter) and K (5% Output Reactor). Options E and K require the add-on
enclosure.
Note 7: All options are available in this size enclosure except E (RFI Filter), R (3% Line Reactor), and K (5% Output Reactor). Only option E combined with
either option R or option K can be installed in the add-on enclosure. Options R and K together require an increase in the size of the P7 Bypass Enclosure.
Contact the factory if all three options are required. Options D (2 Motor “OR”) or A (2 Motor “AND”) for 30 Hp and 40 Hp require the next
size enclosure.
Note 8: Heat sink mounted externally varies the depth dimension depending on the drive size. Depth will not exceed dimension shown.
Note 9: All options are available in this size enclosure except options D (2 Motor “OR”) or A (2 Motor “AND”) for 75 Hp and 100 Hp require the next
size enclosure.