Grass Valley PDR100 - Manual (Page 7)

PDR100 Installation vii
FIGURES
Page
2-1 Circuit Board Slot Nomenclature ..................................................................................... 2-1
2-2 Required Circuit Boards for All Configurations ................................................................ 2-4
3-1 Typical PDR100 Installation with PDX103 Disk Drive Expansion Unit ........................... 3-1
3-2 PDR100 Dimensions for Rack Mounting......................................................................... 3-2
3-3 Dimensions of the RS-422 Connector Panel for Rack Mounting..................................... 3-3
3-4 Dimensions of the PDX103 for Rack Mounting ............................................................... 3-3
3-5 Dimensions of the XLR100 Audio Bypass Unit for Rack Mounting ................................. 3-4
3-6 Complete Rack Slide Set for Right Side of Cabinet and Rack ........................................ 3-4
3-7 Spacing for Mounting Holes in a Standard Rack............................................................. 3-5
3-8 Front Slide Mounting Detail ............................................................................................. 3-6
3-9 Rear Slide Mounting Detail.............................................................................................. 3-6
3-10 Rack Slide Stop Latch ..................................................................................................... 3-7
3-11 Installing Mesh EMI Washers ........................................................................................ 3-10
3-12 Connections and Terminations for Slots 14 - 17 ........................................................... 3-11
3-13 Breakout Cable for the PDR100.................................................................................... 3-12
3-14 Cable Connection Between the PDR100 and RS-422 Connector Panel ...................... 3-13
3-15 Audio Cabling Between the XLR100 and the PDR100 Audio I/O Cards ...................... 3-14
3-16 Location of the Local Area Network (LAN) and VGA Circuit Boards ............................. 3-15
3-17 Connectors for the Keyboard, Mouse Cabling to the PDX103 ...................................... 3-16
3-18 Rear Panel Drawing of the PDX103 Showing the 4 SCSI Connectors ......................... 3-17
3-19 Passive SCSI Bus Termination ..................................................................................... 3-17
3-20 Cabling in a PDX103 Disk Drive Expansion Unit .......................................................... 3-18
3-21 Connections for 601 Serial Digital Video and Analog Audio.......................................... 3-19
3-22 Connections for the Analog Composite Operation ........................................................ 3-21
3-23 Processor Circuit Board Showing the Jumper Locations .............................................. 3-22
3-24 Jumper and DIP Switch Locations and Settings on the VGA-I/O Circuit Board ............ 3-24
3-25 RS422 Circuit Board Showing DIP Switches ................................................................ 3-27
3-26 RS-422 Eight-position DIP Switch Settings ................................................................... 3-28
3-27 RS-422 Four-Position DIP Switch Settings ................................................................... 3-28
3-28 Reference Genlock Circuit Board with Termination Switch
and Jumper Locations ................................................................................................... 3-30
3-29 Master Disk Recorder Circuit Board Showing Square-Pin Test Points ......................... 3-31
3-30 Slave Disk Recorder Circuit Board Showing Square Pin Test Points ........................... 3-32
3-31 Serial Digital I/O Circuit Board Showing Plug Jumpers ................................................. 3-33
3-32 Clock Connections from Serial Digital I/O to Audio Interface Boards............................ 3-35
3-33 Analog Composite Input Circuit Board Showing Plug Jumpers..................................... 3-36
3-34 Audio Clock Cabling for Analog Composite Input.......................................................... 3-37
3-35 Decoder Circuit Board Showing Plug Jumpers ............................................................. 3-38
3-36 Analog Composite Output Circuit Board Showing Plug Jumper Locations ................... 3-39
3-37 Audio Clock from Analog Composite Output Circuit Board ........................................... 3-40
3-38 Audio Clock Cabling from the CAV Input Board ............................................................ 3-41
3-39 Audio I/O Circuit Board Showing Square-Pin Locations................................................ 3-42
3-40 Illustration of the Setup Required to Properly Time Inputs ............................................ 3-44