beautypg.com

Configuring pe 2, Spanning tree configuration example, Network requirements – H3C Technologies H3C S12500-X Series Switches User Manual

Page 147

background image

136

3.

Configure Ten-GigabitEthernet 1/0/3 (a customer-side port):
# Configure Ten-GigabitEthernet 1/0/3 as a trunk port, and assign it to VLAN 200 and VLANs 30
through 90.

[PE1] interface ten-gigabitethernet 1/0/3

[PE1-Ten-GigabitEthernet1/0/3] port link-type trunk

[PE1-Ten-GigabitEthernet1/0/3] port trunk permit vlan 200 30 to 90

# Set the PVID to 200 on the port.

[PE1-Ten-GigabitEthernet1/0/3] port trunk pvid vlan 200

# Enable QinQ on the port.

[PE1-Ten-GigabitEthernet1/0/3] qinq enable

[PE1-Ten-GigabitEthernet1/0/3] quit

Configuring PE 2

1.

Configure Ten-GigabitEthernet 1/0/1 (a customer-side port):
# Configure Ten-GigabitEthernet 1/0/1 as a trunk port, and assign it to VLAN 200 and VLAN 30
through VLAN 90.

system-view

[PE2] interface ten-gigabitethernet 1/0/1

[PE2-Ten-GigabitEthernet1/0/1] port link-type trunk

[PE2-Ten-GigabitEthernet1/0/1] port trunk permit vlan 200 30 to 90

# Set the PVID to 200 on the port.

[PE2-Ten-GigabitEthernet1/0/1] port trunk pvid vlan 200

# Enable QinQ on the port.

[PE2-Ten-GigabitEthernet1/0/1] qinq enable

[PE2-Ten-GigabitEthernet1/0/1] quit

2.

Configure Ten-GigabitEthernet 1/0/2 (the service provider-side port):
# Configure Ten-GigabitEthernet 1/0/2 as a trunk port, and assign it to VLAN 100 and VLAN
200.

[PE2] interface ten-gigabitethernet 1/0/2

[PE2-Ten-GigabitEthernet1/0/2] port link-type trunk

[PE2-Ten-GigabitEthernet1/0/2] port trunk permit vlan 100 200

# Set the SVLAN TPID to 0x8200 on the port.

[PE2-Ten-GigabitEthernet1/0/2] qinq ethernet-type service-tag 8200

[PE2-Ten-GigabitEthernet1/0/2] quit

3.

Configure Ten-GigabitEthernet 1/0/3 (a customer-side port):
# Configure Ten-GigabitEthernet 1/0/3 as a trunk port, and assign it to VLAN 100 and VLAN 10
through VLAN 70.

[PE2] interface ten-gigabitethernet 1/0/3

[PE2-Ten-GigabitEthernet1/0/3] port link-type trunk

[PE2-Ten-GigabitEthernet1/0/3] port trunk permit vlan 100 10 to 70

#Set the PVID to 100 on the port.

[PE2-Ten-GigabitEthernet1/0/3] port trunk pvid vlan 100

# Enable QinQ on the port.

[PE2-Ten-GigabitEthernet1/0/3] qinq enable

[PE2-Ten-GigabitEthernet1/0/3] quit

This manual is related to the following products: