ARAG Bravo 400S Crop sprayer - Manual (Page 105)

105
TECHNICAL DATA
Menu Data Min. Max. UoM DEFAULT Other values that can be set / Notes
Alarms
Nozzles alarms
Nozzle wear check -- -- -- Disabled
Enabled
Visible ONLY with
Pressure sensor enabled
Nozzle wear limit
percentage
1 50 % 10 % Visible ONLY with Pressure sensor enabled
Minimum pressure
alarm
-- -- -- Disabled Enabled
Maximum pressure
alarm
-- -- -- Disabled Enabled
Flowmeter alarms
Minimum flowrate
alarm
-- -- -- Disabled Enabled
Maximum flowrate
alarm
-- -- -- Disabled Enabled
Rev counter alarms
Minimum rotation
speed alarm
-- -- -- Disabled Enabled
Maximum rotation
speed alarm
-- -- -- Disabled Enabled
Working
parameters
Spraying limits
Spraying speed
limit
-- -- -- Disabled Enabled
Minimum spraying
speed 0.4 99.9 km/h 1.0 km/h
0.2 99.9 mph 0.6 mph
Regulation
pressure limit
-- -- -- Disabled Enabled
Minimum regulation
pressure 0.1 99.9 bar 1.0 bar
1 1449 PSI 15 PSI
Flowrate correction
factor
0.25 4.00 -- 1.00
Level correction
factor 0.25 4.00 kg/l 1.00 kg/l
33.38 534.11 oz/gal 133.53 oz/gal
Automatic section control
Sections
overlapping limit
0 100 % 100 %
Perimeter
overlapping limit
0 100 % 0 %
Spray closing delay
-5.0 5.0 m 0.0 m
-16.00 16.00 ft 0.00 ft
Spray opening
advance -5.0 5.0 m 0.0 m
-16.00 16.00 ft 0.00 ft
Guidance
Steering radius
0.0 20.0 m 0.0 m
0.00 65.00 ft 0.00 ft
Reference lines
distance
offset -100.00 100.00 m +000.00 m
-328.08 328.08 ft +000.00 ft
3-point
implement
geometry
settings
Implement upper view
Distance between
connection point
and application
point
0.00 20.00 m 1.50 m
System with 3-point hitch, selected during guided setup
0.00 64.00 ft 4.92 ft
Offset between
connection point
and application
point -20.00 20.00 m 0.00 m
-64.00 64.00 ft 0.00 ft
Implement rear view Implement width
0.50 90.00 m 20.00 m
0.50 290.00 ft 65.62 ft
Towed implement
geometry
Implement upper view
Distance between
implement's rear
axle and the
application point
0.00 20.00 m 0.50 m
System with Towing hitch, selected during guided setup
0.00 64.00 ft 1.64 ft
Distance between
connection point
and implement's
rear axle 0.00 20.00 m 5.00 m
0.00 64.00 ft 16.40 ft
Distance between
tractor's wheels 0.50 5.00 m 1.80 m
0.50 15.00 ft 5.91 ft
Offset between
connection point
and application
point -20.00 20.00 m 0.00 m
-64.00 64.00 ft 0.00 ft
Implement rear view Implement width
0.50 90.00 m 20.00 m
0.50 290.00 ft 65.62 ft
CONTINUES > > >
> > > 17.1 The data and unit of measurement shown
Implement