Cybex 55620H Modular - Manual (Page 144)

ITEM QTY PART NO. DESCRIPTION
1 1 01667 Hand Rail
2 1 5315-201 Cross Tube
3 4 JC780417 BHSCS .50-13 x 1.00
4 11 JS388300 Split Lockwasher .50
5 2 PP0902 10 Plastic Insert 2.00 Sq x 10-14G
6 2 PP090205 Plastic Insert
1.00 x 2.00 x 11 G
7 14 4700C089 Stack Weight 3 x 12
8 2 01141 Spacer
9 1 01142 Pulley Mount Cap
10 1 01143 Pulley Mount
11 1 01144 Upper Pulley Bracket
12 1 01455 Lower Pulley Bracket
13 1 5315-205 Short Top Tube
14 1 5315-203 Adjusting Tube
15 1 5315-202 Ballet Bar Bracket
16 1 01150 Pulley Bracket
17 1 01155 Pivot Tube
18 2 01755 Guide Rod Collet
19 2 01694 Corner Bracket
20 1 5315-307 Ballet Bar
21 2 5310M035 Weight Stack Guide Rod
22 1 5315P011 Adjusting Tube
23 2 PR060005 Weight Bumper
24 2 FB030220 Machinery Bushing
25 4 FB050219 Flange Bearing .62 ID x .75
OD x .50 L
26 2 FB050222 Flange Bearing .75 OD x .88
ID x .75 L
27 6 GP000000 Pulley Assembly 4.50
28 14 GP000004 Pulley Spacer
29 7 GP000203 Pulley Center
30 1 GP000204 Pulley Assembly 3.00
31 2 HC700417 BHSCS .375-16 x 1.00
32 2 HC782817 SHCS .50-13 x 1.00
33 2 HN704000 Hex Nut .375-16
34 2 HN705618 Eye Socket Nut
35 8 HN784000 Hex Nut .50-13
36 2 HS348300 Split Lockwasher .375
37 4 HT582210 Tap Screw #10-32 x .375
38 10 JC700914 FHSCS .375-16 x .62
39 4 HC700414 BHSCS .375-16 x .625
40 6 JC782830 SHCS .50-13 x 2.50
41 2 JC782834 SHCS .50-13 x 3.00
42 4 JS407100 Machinery Bushing .625
43 4 PN660201 Hole Plug
44 2 PP080202 Plastic Insert
45 2 PP080204 Plastic Cap .625 ID x .68 OD
46 1 PU060200 Bumper
47 2 PU060201 Bumper
48 1 01892 Bracket
49 2 HC620430 BHSCS .25-20 x 2.50
50 2 HN624100 Hex Nut .25-20
51 4 PR069400 Recess Bumper
52 1 01692 Threaded Insert
53 1 JC700422 SHCS .375-16 x 1.50
54 2 PP090210 Plastic Insert 2.00 SQ
55 2 HN784900 Nylon Locknut .500-13
56 1 01475 Top Weight Assembly
• 57 2 4700-019 Flange Bearing
58 2 BR030206 Retaining Ring
59 2 HP286819 Spiral Pin
60 1 02106 Half Weight Peg
61 1 JC620415 BHSCS .25-20 x .75
62 1 HS308300 Split Lockwasher .25
63 1 01702 Handle Subassembly
64 2 1670M115 Foam Grip
65 1 02224 Screen (not shown)
66 1 01159 Placard Decal
67 1 4000Y316 Caution Decal
ITEM QTY PART NO. DESCRIPTION
68 1 5208M046 Foam Grip
69 1 5315S028 Cable Subassembly
70 1 4301C096 Half Weight
71 1 02521 Warning Decal
72 1 4800-381 General Warning Decal
73 1 5310P044 Weight Stack Selector Pin
74 1 4800-515 Weight Plate Decal
75 2 HS760106 Flat Washer 1.75 OD .69 .14T
76 1 GQ000206 Snap Link
77 1 5310S040 Handle (not shown)
78 1 51121 Thigh Strap (not shown)
79 1 02203 Straight Handle (not shown)
80 1 51122 Ankle Strap (not shown)
81 1 51073 Hip Harness (not shown)
5605 - Cable Column
Assembly Notes
1. Keep all shipping packages near area of installation.
Standard items include:
• Cable Column Assembly - 5605-9x
• Handrail - 5315-50
• Top Weight Package - 01475
• Weight Pack 1 (3 x 12, black) - 4700S110
NOTE: x denotes specific color.
2. Follow assembly guidelines listed on the 5600
Modular Center Post Assembly & Parts instruction
sheet. Also refer to the steps listed below.
NOTE: Refer to the exploded-view assembly
diagram when performing steps listed below.
3. Lay column on side.
4. Install lower pulley bracket (item 12). Install
upper pivot tube (item 17) and upper pulley
mount (item 11).
5. Install short top tube (13).
6. Set chrome tube into hand rail assembly.
Fasten upper portion finger tight.
7. Attach lower portion of hand rail to column.
8. Route cable. NOTE: Be sure to insert cable
through brass bushing. See Cable Routing
Detail.
9. Install weight stack.
10. Mount column to Modular configuration.
NOTE: This machine shipped with an Owner’s
Manual. Additional copies can be obtained by
contacting your dealer or a Cybex Representative
at 1-888-462-9239.