Comtech EF Data SNM-1001 - Manual (Page 86)

SNM-1001 Network Control Modem Remote Control Operation
Rev. 1 A–27
Bulk Consol
Status
(Continued)
Parameter
Number
Parameter Name
(Command Reference)
Description
(Note 1)
(Note 1)
(Note 2)
(Note 3)
(Note 3)
(Note 3)
(Note 3)
(Note 3)
(Note 3)
(Note 3)
(Note 3)
(Note 2)
(Note 2)
(Note 2)
(Note 2)
(Note 2)
(Note 2)
(Note 2)
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
ADPCM Audio Loopback Jumper
Status (ref. "ALBJ_" command).
RTS TX-IF Control Mode
(ref. "RTSM_" command).
ASYNC Communications
programming ON/OFF (ref. "ASP_"
command).
Interface Loop Timing
(ref. "ILT_" command).
ASYNC TX Overhead Baud Rate
(ref. "TOBR_" command).
ASYNC TX Channel Char. Length
(ref. "TCCL_" command).
ASYNC TX Channel Stop Bits
(ref. "TCSB_" command).
ASYNC TX Channel Parity
(ref. "TOCP_" command).
ASYNC RX Overhead Baud Rate
(ref. "ROBR_" command).
ASYNC RX Channel Char. Length
(ref. "RCCL_" command).
ASYNC RX Channel Parity
(ref. "ROCP_" command).
ASYNC Overhead Communications
Type (ref. "OCT_" command).
Interface Wire Type
(ref. "IWt_" command).
Terrestrial Communications Type
(ref. "TCT_" command).
ASYNC Interface SD Signal
(ref. "ISD_" command).
ASYNC Interface RS Signal
(ref. "ISD_" command).
ASYNC Interface MC Signal
(ref. "IMC_" command).
ASYNC Interface TT Signal
(ref. "ITT_" command).
p54 = n, where 'n' is '0' (off) or '1' (on).
p55 = n, where 'n' is '0' (off) or '1' (on).
p56 = n, where 'n' is '0' (off) or '1' (on).
p57 = n, where 'n' is '0' (off) or '1' (on).
p58 = nnnnn, where 'nnnnn' is the currently programmed
baud rate.
p59 = n, where 'n' is the currently programmed character
length.
p60 = n, where 'n' is the current number of stop bits
programmed.
p61 = xxxx, where 'xxxx' is the currently programmed
parity.
p62 = nnnnn, where 'nnnnn' is the currently programmed
baud rate.
p63 = n, where 'n' is the currently programmed character
length.
p64 = xxxx, where 'xxxx' is the currently programmed
parity.
p65 = n, where 'n' is '0' (RS232) or '1' (RS485).
p66 = n, where 'n' is '2' (2-Wire) or '4' (4-Wire).
p67 = n, where 'n' is '0' (RS422) or '1' (V.35).
p68 = n, where 'n' is '0' (NORMAL) or '1' (INVERT).
p69 = n, where 'n' is '0' (NORMAL) or '1' (INVERT).
p70 = n, where 'n' is '0' (NORMAL) or '1' (INVERT).
p71 = n, where 'n' is '0' (NORMAL) or '1' (INVERT).