Comtech EF Data SNM-1001 User Manual
Page 75
Remote Control Operation
SNM-1001 Network Control Modem
A–16
Rev. 1
Modulator/
Coder
Config
Program
Status
Command:
Response:
MOM_xxxxxxx'cr'
MT_xxxx'cr'
MET_xxx'cr'
MF_nnn.nnnn'cr'
MR_nnnn_mmm.mmm'cr'
MPO_snn.n'cr'
MOP_snn.n'cr'
(Note 1)
SE_xxx'cr'
DENC_xxx'cr'
TDA_xxx'cr'
TC_xxx'cr'
TCP_xxxx'cr'
BBL_xxx'cr'
ADP_xxx'cr'
(Note 2)
SBTR_xxx'cr'
(Note 2)
EMS_x'cr'
(Note 2)
LAW_y'cr'
(Note 2)
ISCL_TX_nnn'cr'
(Note 2)
RD_xxx'cr'
(Note 2)
SD_xxx'cr'
(Note 2)
RR_xxx'cr'
(Note 2)
DM_xxx'cr'
(Note 2)
RTSM_xxx'cr'
ACP_xxx'cr'
(Note 3)
TOBR_nnnnn'cr'
(Note 4)
TCCL_n'cr'
(Note 4)
TOSB_n'cr'
(Note 4)
TOSB_n'cr'
(Note 4)
LPC_xxx'cr'
(Note 4)
NOMP_snn.n'cr'
(Note 5)
MINP_snn.n'cr'
(Note 5)
MAXP_snn.n'cr'
(Note 5)
LCL_xxxx'cr'
(Note 5)
RCL_xxxx'cr'
(Note 5)
OCT_xxxxx'cr'
(Note 3)
TCT_xxxxx'cr'
(Note 3)
ISSD_xxx'cr'
(Note 3)
ISRS_xxx'cr'
(Note 3)
ISMC_xxx'cr'
(Note 3)
ISTT_xxx'cr'
(Note 3)
RSEN_xxx'cr'
MSR_xxx'cr'
RF_xxx'cr''lf']
Modem Operation Mode
Modulator Type
Modulator Encoder Type
Modulator Frequency
Modulator Rate
Modulator Power Offset
Modulator Output Power
Scrambler Enable (ON/OFF)
Differential Encoder (ON/OFF)
Transmit BPSK Data Ordering
Transmit Clock (Source)
Transmit Clock Phase
Baseband Loopback
Interface ADPCM Programming
Interface Subscriber/Trunk Emulation
Interface E&M Signal Type
Interface Transmit Encoding Law
Interface Transmit Service Channel Level
Interface RD Signal
Interface SD Signal
Interface RR Signal
Interface DM Signal
RTS TX-IF Control Mode
Interface ASYNC Programming
ASYNC Transmit Overhead Baud Rate
ASYNC Transmit Channel Character Length
ASYNC Transmit Channel Stop Bits
ASYNC Transmit Overhead Channel Parity
AUPC Local Enable
AUPC Nominal Power Value
AUPC Minimum Power Value
AUPC Maximum Power Value
AUPC Local Carrier Loss
AUPC Remote Carrier Loss
ASYNC Overhead Communications Type
Terrestrial Communications Type
ASYNC Interface SD Signal
ASYNC Interface RS Signal
ASYNC Interface MC Signal
ASYNC Interface TT Signal
Reed-Solomon Encoder (ON/OFF)
Modulator Spectrum Rotation
RF Output (ON/OFF)
This command is used by the Comtech EFData M:N protection
switch to collect information that is necessary to configure
back-up modems.
Notes:
1.
Status only returned when AUPC option is not
enabled.
2.
Status only returned when ADPCM board is installed.
3.
Status only returned when ASYNC board is installed.
4.
Status only returned when ASYNC option is enabled.
5.
Status not returned when local AUPC is enabled.