DAD 141.1 Technical Manual, Rev. 2.2 - February 2014
Page 4 of 54
10.7.
Auto-Transmit Commands
– SG, SN, SW, SA, SH, SM, SO, SV ...................................................... 42
10.7.1.
SG Send Gross Value continuously ............................................................................................................... 42
10.7.2.
SN Send Net Value continuously ................................................................................................................... 42
10.7.3.
SW Send Data String “Net, Gross and Status“ continuously .......................................................................... 42
10.7.4.
SA Send Triggered Average Value automatically .......................................................................................... 42
10.7.5.
SH Send Hold Value continuously.................................................................................................................. 42
10.7.6.
SM Send Peak Value continuously ................................................................................................................ 42
10.7.7.
SO Send Peak To Peak Value continuously .................................................................................................. 42
10.7.8.
SV Send Valley Value continuously ............................................................................................................... 42
10.8.
Logic Input Functions & Status
– AI’n’, IN ......................................................................................... 43
10.8.1.
AI Assign input ‘n’ [ Index 0x2074 and 0x2076 ] ......................................................................................... 43
10.8.2.
IN Read status of the logic inputs [ Index 0x210C ] .................................................................................... 43
10.9.
Logic Output Commands -
IO, OM, S’n’, H’n’, P’n’, A’n’, HT ............................................................ 44
10.9.1.
IO Read / Modify the Status of the logic Outputs [ Index 0x210A ] ............................................................. 44
10.9.2.
OM Control of the logic outputs by the host application [ Index 0x2116 ] ..................................................... 44
10.9.3.
A’n’ Assign action for setpoint ‘n’ [ Index 0x2068 ] ...................................................................................... 45
10.9.4.
S‘n’ Setpoint Value [ Index 0x206C ] .......................................................................................................... 45
10.9.5.
H’n’ Setpoint Hysteresis and Switching Action [ Index 0x206A ] .................................................................. 45
10.9.6.
P’n’ Polarity of Setpoint [ Index 0x2070 ] ..................................................................................................... 46
10.9.7.
HT Hold time for Setpoint Limit [ Index 0x2408 ] ........................................................................................ 46
10.10.
Communication Setup Commands
– AD, NA, BR, DX, OP, CL, TD .................................................. 47
10.10.1.
AD Device Address ................................................................................................................................. 47
10.10.2.
NA Network Address [ Index 0x300C ] ................................................................................................. 47
10.10.3.
BR Baud Rate ......................................................................................................................................... 47
10.10.4.
DX Operation Mode Half-/Full-Duplex ..................................................................................................... 47
10.10.5.
OP Open Device ..................................................................................................................................... 47
10.10.6.
CL Close Devices ................................................................................................................................... 47
10.10.7.
TD Transmission Delay .......................................................................................................................... 47
10.11.
Analog Output
– AA, AH, AL, AM ....................................................................................................... 48
10.11.1.
AA Analog Output Base [ Index 0x2100 ] .............................................................................................. 48
10.11.2.
AH Set Analog High Level [ Index 0x2102 ] .......................................................................................... 48
10.11.3.
AL Set Analog Low Level [ Index 0x2104 ] ........................................................................................... 48
10.11.4.
AM Set Analog Output Mode [ Index 0x2128 ] ....................................................................................... 48
10.12.
Save Calibration and Setup
– CS, WP, SS, AS, GI, PI ...................................................................... 49
10.12.1.
WP Save the Setup Parameters [ Index 0x2066 ] ................................................................................. 49
10.12.2.
SS Save Setpoint Parameters [ Index 0x2066 ] ................................................................................... 49
10.12.3.
AS Save Analogue Output Parameters [ Index 0x2066 ] ....................................................................... 49
10.12.4.
GI Get an Image File from the EEPROM ................................................................................................ 49
10.12.5.
PI Download an Image File to the EEPROM ........................................................................................... 49
10.13.
Trigger Commands
– SD, MT, GA, TE, TR, TL, SA ........................................................................... 50
10.13.1.
SD Start Delay Time [ Index 0x211A or 0x2412] ............................................................................... 50
10.13.2.
MT Measuring Time [ Index 0x210E or 0x2410 ] .............................................................................. 50
10.13.3.
GA Get Triggered Average Value [ Index 0x2008 or 0x2028 ] ............................................................. 50
10.13.4.
TE Trigger Edge [ Index 0x2402 or 0x211C ] ................................................................................... 50
10.13.5.
TR Software Trigger [ Index 0x2062 ] ............................................................................................... 50
10.13.6.
TL Trigger Level [ Index 0x211E or 0x2400 ].................................................................................... 51
10.13.7.
SA Send Triggered Average Value automatically ................................................................................... 51
11.
Use in “Approved” Applications ............................................................................................................ 52
12.
Calibration and Calibration Sequence ................................................................................................... 53
13.
Updates
– Firmware Download .............................................................................................................. 54
