Toshiba IK - TU51CU - Manual (Page 11)

5. 3A Connector Pin Assignments
DC IN 12V DC IN/SYNC
1 +12V
2 +12V
3 GND
4 GND
DIGITAL
1 GND
2 +12V
3 GND(for INDEX)
4 INDEX
5 GND(for HD)
6 HD OUT
7 VD OUT
8 GND(for TRIGGER)
9 TRIGGER
10 VD IN
11 HD IN
12 GND(for VD)
S-VIDEO RGB
1 GND
2 GND
3 Y
4 C
1 GND(for VBS,Y/C)
2 GND(for R/G/B.Y/P r /P b )
3 r /P r out
4 GA'OUT
5
b /P b out
6 VBSA' OUT
7 SYNC OUT
8 GND(for SYNC)
9 -/C OUT
1 RO (+) 31 RO (-) 61 GND 91 GND
2 R1 (+) 32 R1 (-) 62 PIXEL CLK (+) 92 PIXEL CLK (-)
3 R2 (+) 33 R2 (-) 63 FRAME EN (+) 93 FRAME EN (-)
4 R3 (+) 34 R3 (-) 64 FIELD ID (+) 94 FIELD ID (-)
5 R4(+) 35 R4 (-) 65 LINE EN (+) 95 LINE EN (-)
6 R5 (+) 36 R5 (-) 66 TRIGGER D (+) 96 TRIGGER D (-)
7 R6 (+) 37 R6 (-) 67 RESERVE(OUT+) 97 RESERVE(OUT-)
8 R7 (+) 38 R7(-) 68 GND 98 GND
9 R8 (+) 39 R8 (-) 69 GND 99 GND
10 R9(+) 40 R9 (-) 70 GND 100 GND
11 GO (+) 41 GO (-) 71 GND 101 GND
12 G1 (+) 42 G1 (-) 72 GND 102 GND
13 G2 (+) 43 G2 (-) 73 GND 103 GND
14 G3 (+) 44 G3 (-) 74 GND 104 GND
15 G4 (+) 45 G4 (-) 75 GND 105 GND
16 G5 {+) 46 G5 (-) 76 GND 106 GND
17 G6(+) 47 G6(-) 77 GND 107 GND
18 G7 (+) 48 G7 (-) 78 GND 108 GND
19 G8 (+) 49 G8 (-) 79 GND 109 GND
20 G9(+) 50 G9(-) 80 GND 110 GND
21 B0(+) 51 BO(-) 81 GND 111 GND
22 B1 (+) 52 B1 (-) 82 GND 112 GND
23 B2(H-) 53 B2(.) 83 GND 113 GND
24 B3 (+) 54 B3 (-) 84 GND 114 GND
25 B4(+) 55 B4(-) 85 GND 115 GND
26 B5 (+) 56 B5 (-) 86 GND 116 GND
27 B6(+) 57 B6 (-) 87 TXD 117 NC
28 B7(+) 58 B7(-) 88 RXD 118 NC
29 B8 (+) 59 B8 {-) 89 GND 119 NC
30 B9 (+) 60 B9 (-) 90 GND 120 GND
* When using pins to remote(pins 87 to 89), please consult with your dealer.
V:
Precautions on DIGITAL terminal:
* Interference occurring inside the cable may accidentally activate the Trigger if the TRIGGER D
inputs (pins 66 and 96) are open.
If the TRIGGER D input is not used, the TRiGGER D input pin should be either not connected or
connected to RESERVE output pin (pins 67 and 97) ie: (connect pin 66 to pin 67 and pin 96 to 97).
* The RESERVE pins (pins 67 and 97) are provided for an additionai output. If unused they should
be OPEN or connected to Trigger D.
NC pins (pins 117 to 119) should be left OPEN.
11