Carl Goldberg GPMA1968 Tiger 60 ARF - Manual (Page 3)

3
USING THIS INSTRUCTION MANUAL
Before you begin assembling your TIGER 60 ARF, take
some time to read through this entire instruction book. It
is designed to take you step-by-step through the process
and to give you added information on engine and radio
selection and set-up, balancing your aircraft, and flying
your model. The time you spend will speed the assembly
process and help you avoid problems.
PREPARING FOR ASSEMBLY
You will need a work area of approximately 24 x 70" which has
been covered to protect it from adhesive, as well as cuts and
other damage. Many people cover their work area with a
sheet of dry wall (sheet rock) and/or waxed paper t o pre-
vent Zap CA and Epoxy from ruining the work surface.
CONSTRUCTION TIPS
IMPORTANT: ALWAYS READ A FEW STEPS AHEAD.
This will alert you to coming instructions and will help you
plan accordingly.
Using the Parts Identification section, familiarize yourself
with the various items included in your kit box.
As you work, CHECK OFF EACH STEP in the box pro-
vided, so that you are sure you do not forget anything.
Do not hesitate to ask questions. Your local hobby deal-
er and area flyers will most likely be happy to help, as they
want you to have a successful flying experience. You may
also receive technical assistance from Carl Goldberg
Products via e-mail (carlgoldbergproducts.com) or by tele-
phone 678-450-0085.
INTRODUCTION
ADHESIVES & GLUING TECHNIQUES
The ZAP family of adhesives are specially formulated to
firmly glue the plywood, hardwood, and balsa used in your
model and to withstand the vibration and stresses of high
performance flight. ZAP A GAP CA is perfect for most
jobs. However, there are times, such as when you are
installing the stabilizer and fin on the fuselage and want
more set-up time for careful alignment and positioning,
then you should use ZAP ZPOXY™.. Occasionally, you
also will want to use ZAP Super Thin™, which "wicks" into
the surrounding areas. Aliphatic resin glue or similar
water-based glues can also be used, but they will add to
the assembly time because they dry so much more slow-
ly than ZAP A GAP. Remember, whenever using any CA,
you must be careful to read instructions thoroughly, as
you will have only seconds for positioning of parts. Be
sure to trial fit parts together before gluing. Also, never
use watery THIN type CA glue for gluing plywood and
hardwood parts. Thin CA's do not adequately bond these
areas.
CAUTION
Some people may experience an allergic reaction when
exposed to fumes from CA glue or epoxy. As with paints,
thinners, and solvents, it is always important to use glues
only where there is adequate ventilation to carry fumes
away. A fan is recommended. Also, special care must be
taken when using CA, as it will bond skin as well as other
surfaces. ZAP CA remover is a CA solvent which
removes hardened glue from fingers and softens glued
joints for repositioning. Before using any CA, carefully
read all label precautions. When using CA, protective
eye-wear and care in keeping the glue away from the face
is highly recommended. If CA does happen to get into the
eye, hold lid open and flush with water only. Seek imme-
diate medical attention.
COVERING
The TIGER 60 ARF is covered in premium iron on film.
It is not uncommon for ARF's to develop a few wrinkles in
transit. If this is true of your model, the situation is easily
corrected. Before you begin putting the pieces together,
run over the surface of each section with an iron (either
specially designed for airplane use or the more cumber-
some household iron) or use a modeling heat gun. Apply
the heat (set at about 350° F), following along with a soft
cloth and pressing down on the covering as you go
around. This will more firmly set the covering adhesive
into the wood and keep your aircraft covering tight and
smooth in the future.
One of the great advantages of film is that it can be
applied over itself without causing gas bubbles. This
allows you to repair your aircraft, as well as to customize
it in a number of ways. If, due to a flight mishap, you get
a hole or similar covering damage, simply trim away the
ragged edges and then apply a patch, following the direc-
tions that come with replacement film , which is available
at your hobby dealer. In case of a major crash, where
large amounts of the film must be replaced, heat the
damaged covering and then slowly peel up. If you are
applying sufficient heat, the film will come up easily and
leave no color on the wood.