KEYENCE IB Series - Manual (Page 3)

3
„ Sensor amplifier unit
z DIN rail mount type (IB-1000/IB-1050)
z Panel mount type (IB-1500/IB-1550)
„ Sensor head
„ DIN rail mount type, main unit (IB-1000)
Align the claw at the bottom of the main body
with the DIN rail. While pushing the main body in
the direction of the arrow (1), tilt the amplifier in
the direction of the arrow (2).
To remove the amplifier, raise the main body in
the direction of the arrow (3) while pushing it in
the direction of the arrow (1).
„ DIN rail mount type, expansion unit (IB-1050)
Expansion units must be connected to the main unit before they can be used.
Up to 3 expansion units can be connected to one main unit.
1
Remove the expansion protective cover from a IB-1000 (main unit).
2
Install the amplifiers (expansion units) onto a DIN rail.
Do the same as instructed under "DIN rail mount type, main unit."
3
Push the expansion unit into the main unit connector until a
clicking sound can be heard.
4
Install the end units (OP-26751: 2 units per set) (sold separately)
on both sides of the amplifiers (main or expansion units). Secure
the end units in place with screws on top (2 on each end unit).
The end units are mounted in the same way as the amplifiers.
Part Names
Item Description
(1) Main display
Displays the judgment value (P.V. value) and various
setting items.
(2) Laser emission warning
indicator
Turns on while the laser beam is emitted. Flashes
when laser beam is stopped.
(3) Judgment indicator
Indicates whether the judgment value (P.V. value) in
respect to the tolerance setting is HIGH (higher than
the upper limit), GO (within tolerance range) or LOW
(lower than the lower limit).
(4) Auto adjust indicator Turns on while the auto adjust function is operating.
(5) Bank indicator Indicates the bank in use.
(6) Zero shift button
Press this to set the internal measurement value (R.V.
value) to the shift target value.
(7) Sub display identification
indicator
Turns on according to the type of value displayed on
the sub display.
(8) Sub display
Displays the internal measurement value (R.V. value),
analog output value and various settings (selections).
(9) Timing input indicator
If the timing input (external input) is set to level, this
indicator lights while the timing input is on. If the
timing input is set to edge, this indicator turns on for
approx. 0.5 seconds when the timing input is on.
(10) Zero shift indicator
Turns on for approx. 0.5 seconds when zero shift is
executed.
(11) SET button
When making various settings, press this button to
automatically set the setting value.
(12) MODE button
When making various settings, press this button to
start or end the setting or to move the item.
(13) Arrow buttons
Use this to select the setting item or to change the
details displayed on the sub display.
(14) Check indicator Turns on when the check output is on.
(15) Percentage indicator Turns on when the measurement mode is % mode.
(16) Hold indicator
Turns on when the judgment value (P.V. value) is
held.
IB
(1)
(2)
(3)
(4)
(5)
(6) (7) (8) (9) (10) (11)
(16) (15) (14)
(13
(12)
(1)
(2)
(3)
(4)
(5)
(6) (7) (8) (9) (10) (11) (12)
(16) (15) (14)
(13)
Item Description
(1) Laser emission
warning
indicator
Always on when the power is supplied to the sensor head. Flashes
while using the beam axis alignment function. The flashing cycle
quickens as the amount of received light increases and can be uses
as a guide for adjusting the beam axis.
"Beam axis alignment function" (Page 6)
Use a transmitter and receiver with the same serial No.
combination. The operation and accuracy cannot be
guaranteed if units with different serial numbers are used in
combination. The serial No. is attached to the top of the
transmitter and receiver.
Mounting the Amplifier
• When connecting multiple amplifiers (expansion units), first
check to make sure that the power is turned off to all of the
main and expansion units. Installing an expansion unit with
power on may damage this device.
• Push the amplifiers (expansion units) as far as possible into
the main unit. If they are connected at an angle or not inserted
securely, this device could get damaged.
• When connecting the expansion units, make sure to initialize
the expansion units and set the output polarity.
(1)When turning on the amplifier for the first time after con-
necting the sensor head please reference
"Operation When the Power Is Turned On for the First Time" (Page 6)
(2)When initializing the unit please reference
"Initial Reset (Initialize)" (Page 8)
• Expansion units with different settings for output polarity
(such as an NPN output expansion unit to a PNP output main
unit) cannot be connected together.
• Expansion units using DIN rail mount cannot be connected to
a panel mount style main unit.
Mount the amplifiers securely using the end units (OP-26751:
2 units per set) (sold separately) or a commercially available
DIN rail mounting tool to prevent the amplifiers from slipping
and coming off from the DIN rail due to machine vibration.
LASER
R
. o N L A I R E S
R E S A L T
R E S A L T
R . o N L A I R E S
R
. o N L A I R E S
R E S A L T
Laser Receiver Laser transmitter
(1) Laser emission warning indicator
Receiver
Transmitter
Receiver
head
connector
Transmitter
head connector
Point
SERIAL No.
12345678
No.
12345678
Re ceive r Transm itte r
(1)
(2)
(3)
CAUTION
Point
Connector cover
Main unit
Connecter
Expansion unit
Main unit
Point